red lion CR3000 series - User Manual


Inside US: +1 (877) 432-9908 Bulletin No. CR3000- B
Outside US: +1 (717) 767-6511 Drawing No. LP1042
www.redlion.net Released 2018-09-10
-1-
ModelCR3000‐IndustrialOperatorInterf aceWithTFTDisplay
• CONFIGURED USING CRIMSON
®
3.1 SOFTWARE
• THREE OR FOUR ISOLATED SERIAL COMMUNICATION PORTS,
(2 RS-232 and 1 or 2 RS-422/485) - MODEL DEPENDENT
• ONE OR TWO 10 BASE T/100 BASE-TX ETHERNET PORTS
COMMUNICATE WITH UP TO TEN PROTOCOLS
SIMULTANEOUSLY
• ACCEPTS ONE EXPANSION COMMUNICATION MODULE TO ADD
CANOPEN, J1939, PROFIBUS, DEVICENET AND MORE
• ONE USB DEVICE PORT TO LOAD THE UNIT’S CONFIGURATION
OR TRANSFER DATA TO AND FROM A PC
• SD CARD SOCKET FOR LOADING DATABASE IN THE FIELD
• INDUSTRIAL TFT LCD COLOR DISPLAY
• NEMA 4X/IP66 FRONT PANEL
• THREE FRONT PANEL LED INDICATORS
• POWER UNIT FROM 10-30 VDC SUPPLY
• RESISTIVE ANALOG TOUCHSCREEN
GENERALDESCRIPTION
The CR3000 is the perfect solution for applications that require the
operator to monitor and control more than just a single device. With up to
four serial ports and two Ethernet ports, these HMI displays can connect
to multiple serial and Ethernet devices simultaneously, including PLCs,
variable frequency drives, bar code scanners, etc.
The CR3000 performs the functions of a multiple protocol converter,
using up to four high-speed serial communications ports and one or two
10/100 Base-TX Ethernet ports. Ethernet port(s) support up to ten
protocols simultaneously, allowing dissimilar Ethernet based products to
communicate with one another. The SD card slot can be used to collect
your trending and datalogging information as well as load the unit's
configuration file, allowing configuration changes to be made and saved
to the card for later transfer.
The CR3000 range of HMIs is programmed with Red Lion's Crimson
3.1 software. Crimson offers easy to use drag and drop communications
configuration, while the embedded image library allows
the programmer
to create intuitive screens and prompts for the operator. The Crimson
software is available as a no charge download from Red Lion’s website.
CONTENTSOFPACKAGE
- CR3000 Operator Interface
- Hardware packet and plate for mounting unit into panel
- Terminal block for connecting power
- Panel gasket
SAFETYSUMMARY
All safety related regulations, local codes and instructions that appear
in the manual or on equipment must be observed to ensure personal
safety and to prevent damage to either the instrument or equipment
connected to it. If equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may be
impaired.
Do not use the unit to directly command motors, valves, or other
actuators not equipped with safeguards. To do so can be potentially
harmful to persons or equipment in the event of a fault to the unit.
WARNING - EXPLOSION HAZARD - DO NOT D
EQUIPMENT UNLESS POWER HAS BEEN SW
OR AREA IS KNOWN TO BE NON-HAZARDOU
CAUTION: Risk of Danger.
Read complete instructions prior to installation
and operation of the unit.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT
EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF
OR AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT
EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF
OR AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF
COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I,
DIVISION 2.
FOR USE IN HAZARDOUS LOCATIONS:
Class I, Division 2, Groups A, B, C, and D
C
US
U
L
R
LISTED
IND.CONT. EQ.
E317425
T4

Summary

General Product Overview

General Description

Safety Summary

Outlines crucial safety regulations, warnings, and precautions for operating the equipment.

Product Specifications

Power Requirements

Details the power supply voltage, class, and consumption for CR3000 models.

Communication Capabilities

Lists the available communication ports (USB, Ethernet, Serial) and their specifications.

Installation and Powering

Mounting Instructions

Provides step-by-step guidance for mounting the CR3000 operator interface into a panel.

Hazardous Location Installation

Details specific considerations for installing the device in hazardous locations per NEC/CEC.

Connecting Power

Explains how to connect the 10-30 VDC power supply to the CR3000 unit.

Connecting to Earth Ground

Guides on establishing a proper earth ground connection for the unit's chassis.

Module Installation

Communication and Configuration

EMC Installation Guidelines

Configuring the CR3000

Explains how to configure the CR3000 using Crimson software via various ports.

USB Data Transfers

RS232 Ports

Describes the CR3000's RS232 serial ports, pinouts, and LED indicators.

RS485;422 Comms Port

Ethernet Communications

DH485 Communications

Software and Unit Operation

Crimson Software

Describes Crimson software as the configuration tool, available as a free download.

Product Information

Ordering Information

Provides model numbers, descriptions, and part numbers for CR3000 units and accessories.

Limited Warranty

red lion CR3000 series Specifications

General

Brand	red lion
Model	CR3000 series
Category	Control Panel
Language	English