This document describes the RedKite Dreamer Bedside Crib, a versatile sleeping solution for infants, functioning as both a bassinette/travel cot and a co-sleeper.
Function Description:
The RedKite Dreamer Bedside Crib is designed to provide a safe and comfortable sleeping environment for babies from birth up to approximately 4 months, or until they can pull themselves up or sit unaided. It can be used as a standalone bassinette/travel cot or as a co-sleeper attached to an adult bed.
As a bassinette/travel cot, it offers a secure space for the baby to sleep independently. The lowest mattress position is recommended for safety, especially once the baby can support its own weight or sit up. The crib is designed for convenient limited use and is not intended to replace a cot on a long-term basis.
In co-sleeper mode, the crib attaches to the adult bed, allowing the baby to sleep close to the parents while maintaining a separate sleeping surface. This mode features a drop-side function that can be lowered to align with the adult mattress. The attachment system, consisting of fixing belts and an anchor plate, ensures the crib is securely fastened to the adult bed, preventing gaps and movement.
Important Technical Specifications:
- Age/Weight Suitability:
- Bassinette: Suitable for babies who cannot pull themselves up or sit unaided, approximately 0-4 months.
- Maximum weight: 15kg.
- Maximum height: 86cm (whichever comes first).
- Intended for use by children under 3 years of age.
- Mattress Specifications:
- Only the mattress supplied with the product should be used. Do not add a second mattress.
- Mattress size: 850mm x 540mm x 20mm.
- The mattress complies with BS EN 16890:2017.
- Maximum internal size of the cot the mattress is designed for is 865mm x 550mm.
- There must not be more than a 30mm gap between the mattress and the sides and ends of the cot.
- The thickness of the mattress chosen shall be such that the internal vertical height (surface of the top of the mattress to the upper edge of the bed sides) is at least 200mm in the highest position of the bed base.
- Co-Sleeper Dimensions:
- The top edge of the lowering bar must be level with or below the top of the adult mattress.
- The level of the bedside sleeper bassinette mattress must be a minimum of 10cm below the top edge of the lowering bar.
- The height of the parent's mattress must be level with or higher than the side of the cot.
- Customer Care Line: 01454 326 568.
Usage Features:
- Assembly:
- Remove mattress by undoing Velcro straps.
- Ensure base is upright, then lift side rails upwards until they lock.
- Once all four top rails are locked, push the base down.
- Place mattress with Velcro straps facing downwards.
- Thread straps through slots and secure underneath.
- Bassinette Use:
- Zip the liner into the cot (two separate zips: one around sides/back, one for front drop side). Ensure all zips are securely connected.
- Thread the zip loop and eye through the split ring and cover with Velcro flap.
- Insert male and female support rods into the base opposite each other and connect.
- Place mattress inside and secure to liner with Velcro straps.
- WARNING: The lowest mattress position is the safest and should be used when the baby can support its own weight or sit up.
- Folding for Storage:
- Remove mattress and liner.
- Lift the loop in the bottom center of the cot as far as possible.
- Lift side rails up and squeeze the unlocking button on the bottom of the rail.
- With the button held in, lower the rail downwards. Repeat for all side rails.
- While lifting the loop, pull all four corners together and wrap the mattress around it, securing with Velcro straps.
- Drop Side Function (Co-Sleeper):
- Undo zips, squeeze buttons on both sides, and lower the rail until it locks.
- Thread the three straps under the mattress onto the buckles and pull tight.
- ATTENTION: Do not force the zip all the way down; it is designed to stop here.
- Bedside Crib Mode (Co-Sleeper):
- Thread the fixing belt plate between the adult's mattress, pivoting it flat against both the bed base and mattress.
- Connect the ends of the fixing belts to the buckles on each end of the cot and pull tight using the sliding sliders.
- Ensure the cot is tight against the bed.
- WARNING: Always completely raise the drop side when not attached to the adult's bed.
- The attachment system to the adult's bed shall always be kept away from and out of the crib to avoid strangulation risk.
- Never use the crib in co-sleeping mode without the anchor plate attached and locked.
- Ensure plates are securely attached to the adult bed.
- Check tightness of attachment system before each use by pulling the bedside sleeper away from the adult bed.
- Only suitable for beds with straight sides; not for round mattresses or water beds.
- When used in bedside sleeping mode, it should always be fitted to the long side of the bed. Do not fix to the head or bottom of the bed.
- Make sure all straps are secured and tight when used in the bedside sleeper position. Tighten straps periodically.
- Never leave your infant in the product without the top horizontal rail installed in the uppermost position, unless securely attached to the adult bed.
- Always make sure all top and bottom rails are securely locked, in all configurations, before putting an infant child into the unit.
Safety Warnings (General):
- Suffocation Hazard: Infants have suffocated in gaps between extra padding and side of bassinette/cradle and on soft bedding. Never add a pillow, comforter, or another mattress for padding.
- Strangulation/Suffocation Hazard: The top edge of the lowering bar must be level with or below the top of the adult mattress. The level of the bedside sleeper bassinette mattress must be a minimum of 10cm below the top edge of the lowering bar.
- Entrapment Hazard: To prevent death from entrapment, the co-sleeper must be properly secured to the adult bed using the attachment system.
- Strangulation Hazard: When the anchor plate and strap assembly are not in use, store in a safe place not accessible to children.
- Gaps should not be filled with pillows, blankets, or other items.
- Do not allow children to climb or play on or under unit in any configuration.
- Fall Hazard: Remove infant from the bedside sleeper before starting any conversions.
- Before use in co-sleeper mode, make sure the product is securely anchored and positioned. The crib should be locked in the fixed position when the child is left unattended.
- Make sure the connection belts are locked and tensioned properly before laying child in the sleeper. No gaps between the product and the adult mattress shall be present.
- Keep fastening belts out of reach of children.
- Failure to follow warnings and instructions could result in serious injury or death.
- Only use the attachment system supplied. Do not use another.
- Never use the crib in co-sleeper position without the anchor plate attached and locked as shown in the instructions.
- To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep.
- A co-sleeper is designed to provide a sleeping area for an infant until he or she begins to push up on hands and knees or approximately 5 months of age. Move your child to another sleeping product when your child reaches this stage.
- Never raise the level of the bedside sleeper bassinette mattress.
- Never leave your infant in the product without the top horizontal rail installed in the uppermost position, unless securely attached to the adult bed.
- Always make sure all top and bottom rails are securely locked, in all configurations, before putting an infant child into the unit.
- To prevent serious or fatal injury from falls, always keep child within arm's reach.
- General Safety: Be aware of the risk of open fire and other sources of strong heat (electric bar fires, gas fires, etc.) in the near vicinity of the cot/crib.
- Do not use if any part is broken, torn, or missing. Use only spare parts approved by the manufacturer.
- Do not leave anything in the cot or place the cot close to another product which could provide a foothold or present a danger of suffocation or strangulation (e.g., strings, blind/curtain cords).
- Do not use more than one mattress in the cot.
- Do not use your travel cot without the mattress.
- Do not leave a child unattended. Always keep your child in view.
- Ensure the product is correctly assembled before use, with top bars locked straight, center foot firmly on the ground, and mattress in position.
- The travel cot is ready for use only when the locking mechanisms are engaged.
- Position the product on a level and stable surface.
- Keep the product away from trailing cords and flexes.
- Do not use for more than one child at a time.
- Do not allow a child to lift the sides of the mattress up.
- Do not use pillows.
- Do not leave any object inside the product that could reduce its depth.
- Do not position the crib near walls and obstacles to prevent trapping hazards.
- Do not leave small objects inside the product to prevent choking hazards.
- Do not adjust or move the product with the child inside.
- The product must be kept away from electric cables and cords.
- Do not place the product near windows where cords, curtains, or similar objects could pose choking or strangling hazards for the child.
- All assembly fittings should always be tightened properly and care should be taken that no screws are loose as a child could trap parts of the body or clothing (e.g., strings, necklaces, ribbons for babies dummies, etc.), which would pose a risk of strangulation.
- Do not use the body of the crib without its frame.
- Always use the crib with the drop side rail in place.
Maintenance Features:
- General Care:
- Do not use excessive force when adjusting the product.
- Always store the product in a dry place.
- The correct use and maintenance of this product is essential.
- Keep the fastening belts away from the reach of children.
- Cleaning:
- Fabrics and the mattress may be spot cleaned using a sponge with a mild soap and warm water solution.
- Leave to dry in a ventilated area away from direct sunlight.
- Do not dry clean, machine wash, bleach, or tumble dry.
- Metal parts may be cleaned with a damp cloth. Always wipe dry.
- Clean plastic parts with a mild soap and warm water solution.
- Avoid leaving the product in direct sunlight for prolonged periods of time as this may cause fabrics to fade.
- Maintenance Checks:
- Check that nothing is loose or broken and that no sharp edges have been exposed. Replace any damaged parts immediately.
- Routinely inspect all studs, nuts, and screws for tightness.
- Do not use replacement parts other than those approved by the manufacturer or distributor. Failure to do this may invalidate your warranty.
- Do not use crib if any parts are missing, damaged, or broken. Contact Red Kite for replacement parts and instructional literature if needed. Do not substitute parts.
- All assembly fittings should always be tightened properly and fittings should be checked regularly and retightened as necessary.
To Next Page
Need help?
General
