Regency Classic F2450M

Need help?

Do you have a question about the Regency Classic F2450M and is the answer not in the manual?

Overview

Function Description
Important Technical Specifications
Usage Features
Maintenance Features

The Regency F2450M is a classic freestanding wood stove designed for efficient heating and aesthetic appeal, suitable for various residential settings, including mobile homes with specific installation requirements. It is certified to comply with 2020 U.S. Environmental Protection Agency (EPA) particulate emission standards, using cord wood, and has been tested to ASTM E3053, achieving a particulate emission rate of 2.3 g/hr.

Function Description

The F2450M wood heater is designed to burn natural wood only, providing heat for residential spaces. It operates by combusting wood in a firebox, with heat radiating into the room and exhaust gases exiting through a chimney system. The stove features a draft control lever to regulate the burn rate and a fan system (optional) to distribute heat more effectively. It is designed for optimal efficiency when burning air-dried seasoned hardwoods.

Important Technical Specifications

Emissions: 2.3 g/hr particulate emissions (EPA 2020 certified).
Heat Output: Ranges from 14,200 BTU/hr to 53,600 BTU/hr.
Efficiency: Determined using the B415 method.
Dimensions (Unit):
- Width: 24" (610mm)
- Depth: 21-1/4" (540mm)
- Height (from floor to top of flue collar): 34-5/8" (879mm)
- Height (from floor to top of unit): 32-1/8" (817mm)
Flue Collar Height: 27-1/8" (690mm) from floor.
Flue Center-Line to Back: 13-1/8" (333mm).
Flue Center-Line to Side: 12-1/16" (306mm).
Outside Air Dimensions:
- From rear: 4-9/16" (115mm)
- From side: 6-13/16" (173mm)
Minimum Alcove Clearance:
- Ceiling Height: 83"
- Depth: 48"
Minimum Clearances to Combustible Materials (with Airmate):
- Residential Installation "C" Vent (Single Wall):
  - From Unit (A): 16" (406mm)
  - From Unit (B): 9.5" (241mm)
  - From Corner (C): 8" (203mm)
  - From Corner (D): 28" (711mm)
  - From Flue Center-Line (E): 16" (406mm)
  - From Flue Center-Line (F): 20" (508mm)
- Residential Close Clearance (To be installed with required pipe components):
  - From Unit (A): 15" (381mm)
  - From Unit (B): 8" (203mm)
  - From Corner (C): 6" (152mm)
  - From Corner (D): 27" (686mm)
  - From Flue Center-Line (E): 14.5" (368mm)
  - From Flue Center-Line (F): 18" (457mm)
Floor Protection (Ember Protection only required):
- Canada: Extends at least 18" beyond the fuel loading side and 8" on the sides and back.
- USA: Extends at least 16" beyond the fuel loading side and ash removal opening, and at least 8" on the sides and back.
Chimney Requirements: Must be connected to a listed factory-built chimney suitable for solid fuels (ULC629 in Canada or UL-103HT in the USA) or a code-approved masonry chimney with flue liner.
Electrical: 120V AC, 60 Hz for fan operation (if installed).

Usage Features

Fuel Type: Designed exclusively for natural wood. Burning treated wood, garbage, plastics, or other non-wood materials is prohibited and can damage the stove and release toxic fumes.
Draft Control: A draft control lever allows users to adjust the burn rate, impacting heat output and fuel consumption.
First Fire: Specific instructions are provided for the initial fires to cure the paint and prevent damage.
Ash Disposal: An ash drawer (optional) facilitates easy removal of ashes.
Door Handle: A latch adjustment mechanism allows for tightening the door seal over time.
Air Intake: Features an outside air kit option for improved combustion and reduced indoor air quality impact.
Safety Decal: Includes a safety decal with important warnings and clearances.
Mobile Home Installation: Specific guidelines and requirements for installation in mobile homes, including mandatory outside air kit and proper grounding.

Maintenance Features

Annual Maintenance: A detailed schedule includes:
- Complete unit clean out: Annually.
- Inspect air tube and bricks: Annually.
- Adjust door gasket assembly: Annually (replace if unable to obtain a tight seal).
- Inspect condition and seal of glass gasket and door gasket: Annually (replace if required).
- Paper test: Annually to check door seal integrity.
- Check and lubricate door hinge + latch: Annually (use only high temperature anti seize lube).
- Check glass for cracks: Annually (replace if required).
- Clean blower motor: Annually (disconnect power supply, remove, and clean).
- Inspect and clean chimney: Annually (professional chimney cleaning recommended).
Secondary Air Tube Removal/Installation: Instructions for removing and installing the secondary air tubes for maintenance or replacement.
Vertical Stainless Deflector Replacement: Instructions for replacing the vertical stainless deflector.
Glass Replacement: Detailed steps for replacing the Neoceram ceramic glass, emphasizing the use of genuine Regency parts and proper gasket installation.
Chimney Cleaning: Regular chimney cleaning is crucial to prevent creosote buildup and ensure safe operation.
Creosote Inspection: Regular inspection for creosote buildup is recommended, especially during the heating season.
Door Gasket Adjustment: The door latch mechanism allows for adjustment to maintain a tight seal as the gasket material compresses over time.