EasyManua.ls Logo

Remington RM2100 - User Manual

Remington RM2100
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Printed In USA
Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
OperatOr’s Manual
Form No. 769-10790
(May 20, 2015)
Safe Operation Practices ........................................ 2
Assembly & Set-Up .................................................. 5
Controls & Operation .............................................. 8
Service .....................................................................10
Troubleshooting .....................................................12
Parts/Warranty .............. See Separate Supplement
Table of Contents
NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all
models and the model depicted may differ from yours.
Snow Thrower
Single-Stage
(200 Series)

Table of Contents

Questions and Answers

  • E
    ellisdonnaJul 30, 2025
    Why my Remington RM2100 Snow Blower engine fails to start?
    • G
      Gabriella LucasJul 30, 2025
      There are several possible reasons why your Remington Snow Blower engine might fail to start. It could be due to the choke not being in the CHOKE position, a disconnected spark plug wire, an empty or stale fuel tank, the engine not being primed, a faulty spark plug, or the safety key not being fully inserted into the switch. Make sure the choke is in the CHOKE position, the spark plug wire is connected, the fuel tank has clean, fresh fuel, the engine is properly primed, the spark plug is in good condition, and the safety key is fully inserted.
  • J
    John OlsonAug 3, 2025
    What to do if my Remington RM2100 fails to discharge snow?
    • N
      Nancy PetersonAug 3, 2025
      If your Remington Snow Blower fails to discharge snow, the issue might be a clogged chute assembly or a foreign object lodged in the auger. Stop the engine and disconnect the spark plug wire. Clean the chute and inside of the auger housing using a clean-out tool. Also, stop the engine immediately and disconnect the spark plug wire to remove any foreign objects from the auger. Additionally, check and adjust the auger control cable or replace the auger drive belt if they are damaged or loose.
  • R
    randallcolemanAug 8, 2025
    Why is my Remington RM2100 engine running erratically?
    • C
      Christina StephensAug 8, 2025
      An erratic engine in your Remington Snow Blower may stem from several causes. Ensure the engine isn't running on CHOKE; if it is, move the choke lever to the RUN position. Stale fuel, or water/dirt in the fuel system can also cause this issue; in that case, replace the fuel. If these steps don't resolve the problem, the carburetor may be out of adjustment or the engine may be over-governed.
  • C
    Chad PattersonAug 12, 2025
    What to do if my Remington RM2100 Snow Blower has excessive vibration?
    • M
      Mary MyersAug 12, 2025
      If your Remington Snow Blower is vibrating excessively, immediately stop the engine and disconnect the spark plug wire. Check for any loose parts or damage to the auger. Tighten all bolts and nuts. If the problem persists after these checks and repairs, further assistance may be needed.
  • S
    Shawn PowellAug 16, 2025
    Why Remington Snow Blower unit fails to propel itself?
    • P
      ppetersAug 16, 2025
      If your Remington Snow Blower isn't moving on its own, it could be due to an improperly adjusted auger control cable, a loose or damaged auger drive belt, or excessively worn auger paddles. Adjust the auger control cable, replace the auger drive belt, or replace the auger paddles.
  • R
    Rose HamiltonAug 20, 2025
    What to do if Remington RM2100 Snow Blower augers continue to rotate?
    • F
      frederick43Aug 20, 2025
      If the augers on your Remington Snow Blower continue to rotate, check the routing of the auger control cable along the handle. If the problem persists, further assistance may be needed.
  • V
    Valerie KellyAug 26, 2025
    How to fix Remington Snow Blower chute that fails to easily rotate 190 degrees?
    • M
      Mr. Paul Gill IIAug 26, 2025
      If the chute on your Remington Snow Blower doesn't rotate easily, it might be assembled incorrectly. Disassemble the chute control and reassemble it.

Summary

Safe Operation Practices

Safety Alerts and Warnings

Critical safety warnings, DANGER, and PROPOSITION 65 notices.

Training, Preparation, and Fuel Handling

Clearing a Clogged Discharge Chute

Safety Procedure

Step-by-step instructions for safely clearing a blocked discharge chute.

Controls & Operation

Auger and Drive Controls

How to operate the auger and engage the machine's drive system.

Chute Adjustment and Direction

Adjusting chute pitch, rotation, and features like E-Z Chute.

Engine Starting and Safety Features

Procedures for starting the engine and using safety key features.

Clogged Chute Clearing

Procedure for safely clearing a blocked discharge chute.

Troubleshooting

Engine Start and Running Issues

Power and Vibration Problems

Propulsion and Auger Issues

Discharge and Chute Problems

Remington RM2100 Specifications

General IconGeneral
Clearing Width21 inches
Throw DistanceUp to 25 feet
Start TypeRecoil
Engine Displacement (cc)123 cc
Forward Speeds1
Reverse Speeds0
Chute ControlManual
Scraper BarYes
Warranty2-year limited
Engine4-cycle
Intake Height13 inches
Starting SystemManual

Related product manuals