7
Never leave the pipe cutting machine running unattended. Switch off the
pipe cutting machine during longer work breaks and pull out the mains plug/
Electrical devices can cause hazards which lead to material damage or
injury when left unattended.
Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the pipe cutting
machine safely may not use this pipe cutting machine without supervision
or instruction by a responsible person.
Otherwise there is a risk of operating
Only allow trained persons to use the pipe cutting machine.
may only use the pipe cutting machine when they are over 16, when this is
necessary for their training and when they are supervised by a trained operative.
The pipe cutting machine is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge unless they have been given supervision or
instruction concerning the use of the pipe cutting machine by a person
responsible for their safety.
Children must be supervised to ensure that they
do not play with the pipe cutting machine.
Check the power cable of the pipe cutting machine and extension leads
Have these renewed by qualifi ed experts or an authorised
REMS customer service workshop in case of damage.
Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section.
Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m w
ith cable cross-section 2.5 mm².
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².cable cross-section 1.5 mm², from 10 – 30 m w
Safety notes for batteries, rapid chargers,
WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
Failure to heed the instructions can result in electric shock,
fi re and/or severe injuries.
Save all warnings and instructions for future reference.
See also www.rems.de → Downloads → Operating Instructions and
www.rems.de → Downloads → Safety Data Sheets → Batteries.
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Electrical device complies with protection class II
Not suitable for using outdoors
Environmental friendly disposal
Use for the intended purpose
WARNING
REMS Cento
and REMS DueCento are intended for the purpose of cutting and deburring the inside and outside of pipes.
All other uses are not for the intended purpose and are therefore prohibited.
Guidelines for use of REMS cordless tools, batteries, rapid chargers, power supply units.
See www.rems.de → Downloads → Instruction Manuals → Cutting, chamfering, deburring: OTHER DOCUMENTS
REMS Cento Basic: Pipe cutting machine, ring spanner size 27/17, instruction manual.
Pipe cutting machine, ring spanner size 27/17, one each of pipe guides Ø 75 mm and 110 mm, RF cutting wheel, operating instructions.
REMS Cento
22 V Basic: Cordless pipe cutting machine, Li-Ion 21.6 V, 5.0 Ah batte
ry, ra
pid charger, ring spanner size SW 27/17, instruction manual.
REMS DueCento Basic: Pipe cutting machine, ring spanner size 27/17,
2 height adjustable pipe rests 1 for pipes Ø 100 – 225 mm, Ø 4 – 8",
feed lever, spring plug, instruction manual.
1.2. Article numbers REMS Cento REMS Cento RF
REMS Cento
Pipe cutting machine 84500
REMS cutting wheel Cu-INOX for pipes of the press fi tting systems of
stainless steel, copper, carbon steel 845050
REMS cutting wheel Cu especially for pipes
of the press fi tting systems of copper 845053
REMS cutting wheel St for steel pipes, cast pipes (SML) 845052
REMS cutting wheel C-SF especially for pipes of the press fi tting systems/
push fi tting systems of carbon steel, simultaneously produces a chamfer 845055
REMS cutting wheel V, s 10, for plastic and composite tubes,
wall thickness s ≤ 10 mm 845051
REMS cutting wheel P, s 21, for plastic and composite tubes,
wall thickness s ≤ 21 mm 845057
REMS cutting wheel RF 845054
REMS battery Li-Ion 21.6 V, 5.0 Ah 571581
REMS battery Li-Ion 21.6 V, 9.0 Ah 571583
er 1
er 1
Voltage supply 220 – 240 V, instead of 21.6 V, 40 A batteries
Feed lever REMS DueCento 845218 845218
089082 089082 089082 089082
Base frame, movable 849310 849310
of tubular stainless steel 845110
Roller insert for cutting pipes Ø 40 – 100 mm 845060
Ring spanner size 27/17 849112
REMS Herkules 3B, material rest with tripod 120120
REMS Herkules Y, material rest with clamping device 120130
REMS Herkules XL 12" 120125 120125 120125
To Next Page
Loading...