Retevis Ailunce HD2 - Radio Menu Settings - Main Set; Squelch Setting; Key Define Function; Scan Mode Setting

05
Radio Menu Setting- Main Set
NO. Menu Denition
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Squelch
Save
A/B Time
Double PTT
Bluetooth
BTRebind
Voice
Zone Name
VOX Delay
Mic Gain
Hang Up
Tx Channel
Key Dene
Backlight
Brightness
Key Beep
Key Lock
Lock Mode
CH-Mode
S/D Mode
Scan Mode
Save CH
Delete CH
Roger
Time
Menu Exit time
Miss Call Set
Rx Info Bright Set
DMR TX Beep
FM TX Beep
Night Mode
Noise Tail
0~9 levels (In analog mode, when the Squelch level is set high, the background hiss noise will be
muted. However, only the stronger signals will be heard. If the Squelch level is set low, this will allow
lower strength signals to be heard, but the radio will now be more prone to hearing the background
hiss noise from time to time.)
Power saving ratio (It indicates the batte saving rate, the highest rate is 1�4. the higher you select,
the more power saved. at the same time, the receiving will be a little delayed, but normally we
don't feel the delay.)
Set Band A or Band B switch time from 01 to 10S.
Choose to use double PTT or not. When double PTT is on, the programmed side key function will not work.
Turn on or o the Bluetooth function. When connected to Bluetooth voice device, the Bluetooth
icon will change to red.
Conrm Bluetooth.
Voice Announcements.
Turn on the function to display zone name.
Set VOX delay time.
Set the mic gain level.
Set the digital hang up time.
①O: when the hang-up function is o, it will transmit with the current channel contact.
② 1S ~ 10S: If the current channel has received the call within this hang-up time range, it will be
transmitted with the received contact. If it is out of the hang-up time, it will transmit with the
current channel contact.
Busy channel settings.
Key1 and Key2 sho or long press functions as below: OFF, Power, Scan, radio (FM Radio）, Wake
up, Relay, Key Call 1-6, VOX, Kill (Remote kill), Zone Plus, Zone Minus, DMR slot, Promiscuous,
Manual Dial, CH-Mode, Reverse, Bluetooth , 0.5W Power, FM Call, Voltage, NOAA, Analog Monitor,
TX Digital Deviation, 1000Hz,1450Hz,1750Hz,2100Hz;
Key 1 or Key 2 long press extra functions as below:
TX-DSW, M-MONI, Tx1000, Tx1450, Tx1750, Tx2100.
Sho press [*scan] button to switch SK1 or SK2 sho or long press operation.
Screen backlight time：1s-120s；Cont: The backlight stays on.
Level 1-10; The higher the number, the higher the brightness.
Keyboard tone.
Choose manual or auto Lock.
Keyboard, keyboard+CH, keyboard+CH+PTT.
Frequency: Frequency+Channel number.
Name: Channel name.
CH: Channel mode.
Choose single band and dual band standby.
Carrier, Time, Search.
Time mode (TO): When the radio detects a signal it will stop scanning and will pause for 5 seconds
before scanning again even if the signal is still present.
Carrier mode (CO): When the radio detects a signal it will stop scanning and will stay on the same
frequency and will resume scanning after 5 seconds when the signal ends.
Search mode (SE): When the radio detects a signal, it will stop on that frequency and will not move
on, even if the signal ends.
Long press [*scan], it will begin to scan. Up and down key to change the scan direction, Press any
key to exit scan.
Storage channel: If displays “CH-01”，means it already a storage channel. If display “002”, means it
can save it as a new channel.
Delete channel. Same operation as above.
Transmit end tone
Set local time. Use *Scan button to switch year, month, day time.
Set menu exit time.
Choose to check the miss call or not.
Choose if the led bright when receiving.
Digital transmit Talk Permit tone
Analog transmit beep tone
Switch to night mode
Repeater tail tone elimination.