REVELL Dodge Viper SRT10 ACR - User Manual

DECAL PLACEMENT
13
Aluminum
Gloss Black
Gloss Red
Flat White
Semi Gloss Black
Yellow
Steel
Turn Signal Amber
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Alminium
Noir brilliant
Rouge briliant
Blanc mat
Noir satiné
Jaune
Acier
Ambre transparent
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
DODGE VIPER SRT10 ACR
KIT 4243 85424300200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85424300200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
Kit 4243 - Page 8
The Dodge Viper SRT10 ACR
(American Club Racer) is a Viper
built for the hard core enthusi-
ast. The ACR is equipped with a
V-10 engine and six speed man-
ual transmission plus an exten-
sive aerodynamic package. This
Viper is street-legal but drives
and handles like a true race car.
Your Revell model features an
opening hood with a detailed 600
bhp V-10 engine, opening trunk,
a detailed interior, aerodynamic
front air splitter, fixed front dive
plates, rear wing, lightweight racing
style wheels and authentic factory
graphics with carbon fiber panels.
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
* REPEAT PROCEDURE
* R E P E T E Z L E P R O C E D E
``` ` ``

Summary

Preparation and Decal Application

Decal Application Guide

Step-by-step instructions for applying decals to the model for best results.

Engine Assembly

Engine Transmission Half Assembly

Assembly of the left and right engine/transmission halves, made of aluminum.

Cylinder Head and Rocker Cover Installation

Attaching cylinder heads and rocker covers, some in gloss red, to the engine block.

Exhaust Manifold and Front Engine Parts

Mounting exhaust manifolds and the front engine components made of aluminum.

Accessory Components Installation

Installing starter, power steering pump, and belt assembly to the engine.

Exhaust and Suspension Assembly

Chassis and Exhaust Pipes

Attaching semi gloss black chassis and aluminum exhaust pipes for the model.

Steering and Tie Rod Components

Installing the steering rack and front/rear tie rods made of semi gloss black plastic.

Suspension Assembly

Differential and Drive Shaft

Mounting the differential cover and drive shaft for the suspension.

Rear Suspension Components

Assembling rear lower A-arms, springs, and disc brakes for the rear suspension.

Front Suspension and Disc Brakes

Installing front shocks, splitter/suspension, and disc brakes on the front.

Radiator Assembly

Radiator and Electric Fans

Installing the aluminum radiator and twin electric fans to the model.

Air Filter and Intake Assembly

Air Duct Components

Attaching the top and bottom air duct parts to the intake assembly.

Radiator Hose

Connecting the upper radiator hose, specified as flat black.

Tire Assembly

Small Tire Mounting

Fitting small tires, including pin retainers, onto the front wheels.

Large Tire Mounting

Fitting large tires, including pin retainers, onto the rear wheels.

Wheel Finishes

Details on front and rear wheel finishes, including chrome for the rims.

Interior Assembly

Firewall and Parking Brake

Installing the firewall and parking brake components.

Shift Lever and Brake Unit

Attaching the shift lever and power brake unit to the interior frame.

Seat and Door Panel Installation

Mounting front seats and interior door panels to the model.

Dashboard and Steering Column

Installing the dashboard, steering column, and steering wheel.

Headlights and Windshield Assembly

Headlight Buckets and Covers

Installing chrome headlight buckets and clear headlight covers.

Front Air Dams and Driving Lights

Attaching front air dams, driving lights, and their lenses.

Windshield and Rear View Mirror

Fitting the clear windshield and chrome rear view mirror.

Rear Assembly

Rear Hatch and Bumper

Attaching the rear hatch, gas cap, and bumper.

Taillights and Backup Lights

Installing transparent red taillights and clear backup lights.

Rear Window

Fitting the clear rear window to the model.

Rear Wing Assembly

Rear Wing Components

Assembling the rear wing foil, sides, and supports.

Hood and Body Assembly

Hood Installation

Fitting the model's hood.

Panels and Mirrors Assembly

Body Side Panels

Attaching the left and right body side panels.

Vent Panels

Installing the left and right vent panels.

Side View Mirrors

Mounting the left and right side view mirrors.

Decal Placement

Front and Rear Decals

Placement guide for decals on the front and rear of the model.

Side and Top Decals

Placement guide for decals on the sides and top of the model.

REVELL Dodge Viper SRT10 ACR Specifications