TECHNICAL
DATA
Turntable drive:
Turntable speeds.
Speed accuracy:
Platter
(Turntable proper):
Weight
(Mass):
Run up time:
Braking time:
Wow and flutter-:
weighted:
I i near:
Rumble to signal
raltos
-
:
Tone arm:
Lateral tracking angle error
Skating
compensation:
Tracking force:
Tone arm lowering:
Muting:
Tone
arm follow-up:
Run-out switch:
Automatic functions:
Swivelling the tone arm
support
in:
Swivelling
the tone arm
support out:
Ouartz
referenced
direct drive
33 33 and
45 00 rpm
o01%
Diameter'12.32
inches
(313
mm)
4 lbs
10 ozs
(21
l<g)
better than
2
seconds
at
33 33
rpm
better than 2 seconds
from
45
to 33 33
rpm
berter than
0.05%
better than
0.'l
%
better than 48 dB
(DlN
45539
A
weighting)
better than
50
dB
(DlN
45539
A
weighting
plus
20 Hz
high
pass)
better
than 70 dB
(DlN
45539
B)
linear tracking tone arm
with
servo-electronic
f ol low-up
control
less than O.50
not required
with a
linear
tracking system
adjustable from
B
.20 mN
(08.29)
electronically controlled,
pneumatically
damped
electronically muted
until
the
stylus
has
contacted the disc
Opto-electronic sensing
with
LED
as light
source.
servo
electronics
and DC
motor
AutomaticallV
act'vated
via
servo-electronics
tu
rnta
ble
platte
r
sta
rts to rotate
at the
selected
speed
a)
immediate
lifting
of the
ca rtridge
b) tone
arm
returns
to
start
position
c) turntable
stops, stylus
illu-
mination
switched off
Operating
controls:
Turntable
drive:
Tone
arm:
General:
Components
list:
Electric current supply
(solder
connections).
Fuse:
Weight
Dimensions(WxHxD)
Dust cover
closed.
Dust cover
open:
2 tactile
feedback keys
for
33 33 and 45
rpm,l
power
switch
3 tactile feedback
keys for fast
inward
or outward movement
plus
lowering and lifting
of
the
pick-up
cartridge;
built-in
stylus
rilumination.
21 lC's,
'19
transistors, 29 diodes,
4 LEDs. 2
bridge
type rectifiers
10011101120v
+
10%
20ol22ol24ov
+
10%
50 60
Hz
'100.
1 20V. O
4A
slow blow
200. 240 V:0.2 A slow-blow
20 lbs
'1
oz
(9'1
kg)
17 .7 x5 6 x 15.6 inches
(449x142x395
mm)
herght
13
4 inches
(340
mm)
"measured with
IEEE 193 1911
weighting
and an optimally
centered,
direct cut
laquer, L* R
**all
rumble measurements
taken
in
position
"mono"
with
a
statically discharged disc and the
"new"
RIAA reproduce equali
zation.
THE REVOX
PRODUCT
RANGE
REVOX
offers a complete
range
of
hi-fi
system
components. They may be used together
with
your
model 8795
turntable
in
any desired
combi-
nation:
REVOX 87 7 Iape-recorder
REVOX 8750 integrated amplifier
REVOX 8760
digital synthesizer
FMtuner
REVOX B7B0 microprocessor
synthesizer
FM receiver
Ask
your
dealer for the
REVOX full-line
catalog
To Next Page
Loading...
Need help?
General
