Rheem RH1P2417STANJA - Page 29

29
3.13.6.2 ELECTRICAL DATA – WITH ELECTRIC HEAT: (-)H1T - continued
7.2/9.6 3/60 3-3.2 MULTIPLE CKT 1 20.0/23.1 4.6 31/35 35/35
RXBH-24A20C
7.2/9.6 3/60 3-3.2 MULTIPLE CKT 2 20.0/23.1 0 25/29 25/30
4824S RXBH-24A25C* 18.0/24.0 3/60 6-4.0 SINGLE 50.0/57.8 4.6 69/78 70/80
6021S 9.0/12.0 3/60 3-4.0 MULTIPLE CKT 1 25.0/28.9 4.6 37/42 40/45
6024S
RXBH-24A25C
9.0/12.0 3/60 3-4.0 MULTIPLE CKT 2 25.0/28.9 0 32/37 35/40
RXBH-24A30C* 21.6/28.8 3/60 6-4.8 SINGLE 60.0/69.4 4.6 81/93 90/100
RXBH-24A30C
10.8/14.4 3/60 3-4.8 MULTIPLE CKT 1 30.0/34.7 4.6 44/50 45/50
(6024S only)
10.8/14.4 3/60 3-4.8 MULTIPLE CKT 2 30.0/34.7 0 38/44 40/45
RXBH-24A07D 7.2 3/60 3-2.4 SINGLE 8.7 3.2 15 15
RXBH-24A10D 9.6 3/60 3-3.2 SINGLE 11.6 3.2 19 20
4824S RXBH-24A15D 14.4 3/60 3-4.8 SINGLE 17.3 3.2 26 30
6021S RXBH-24A18D 17.0 3/60 6-2.84 SINGLE 20.4 3.2 30 30
6024S RXBH-24A20D 19.2 3/60 6-3.2 SINGLE 23.2 3.2 33 35
RXBH-24A25D 24.0 3/60 6-4.0 SINGLE 28.8 3.2 40 40
RXBH-24A30D
28.8 3/60 6-4.8 SINGLE 34.6 3.2 48 50
(6024S only)
? Heater Kit Connection Type A=Breaker B=Terminal Block C=Disconnect Pullout
*Values only. No single point kit available.
NOTES:
• Electric heater BTUH - (heater watts + motor watts) x 3.412 (see airflow table for motor watts.)
• Supply circuit protective devices may be fuses or “HACR” type circuit breakers.
• Motor load is included in single circuit or circuit 1 of multiple circuits.
• Heater loads are balanced on 3 phase models with 3 or 6 heating elements only.
• Electric heater kits are not permitted for use with 115 volt air-handlers (A voltage).
• J Voltage (208/240V) single phase air-handlers are designed to be used with single or three phase 208/240V electric heaters. To connect 3
phase power to the air handler terminal block, bring only two leads to terminal block, cap, insulate, and fully secure the third lead.
• Do not install 480V electric heaters in 208/240V air-handlers.
• Do not install 208/240V electric heaters in 480V air-handlers.
• If the heater kit is listed under both single and multiple circuits, the heater kit is shipped from factory as multiple circuits. For single phase appli-
cations, Jumper bar kit RXBJ-A21 and RXBJ-A31 can be used to convert multiple circuits to a single supply circuit. See Section 6.2 for details.
AIR HANDLER
MODEL
(-)H1T
HEATER
MODEL
NO.
HEATER
KW
(208/240V)
(480V)
PH/HZ
NO.
ELEMENTS
- KW PER
TYPE SUPPLY
CIRCUIT
SINGLE CIRCUIT
MULTIPLE CIRCUIT
HEATER
AMPS
MOTOR
AMPS
MINIMUM
CIRCUIT
AMPACITY
MAXIMUM
OVERCURRENT
PROTECTION