To Next PageTo Next Page
Need help?Do you have a question about the RHOSS THAITY 105 and is the answer not in the manual?
Identifies the ELECTA Series product, models THAITY 105-110-116.
Company's declaration of product compliance with essential safety requirements.
Company's declaration of product compliance with safety requirements.
Manufacturer's declaration of product compliance with safety requirements.
Company's declaration of product conformity with safety requirements.
Wiring diagram for the THAITY 105 model, showing component connections.
Wiring diagram for the THAITY 110 model, detailing component connections.
Wiring diagram for the THAITY 116 model, illustrating component interconnections.
Details on connecting the ON/OFF contact for machine control.
Explanation of the Pump 1 activation via L-K input.
Configuration of set points for radiant and fan-coil applications.
Methods for enabling DHW production using probes or thermostats.
Manual handling, safety, and product care advice.
Manufacturer's liability limitations and warranty void conditions.
Essential safety guidelines for installation and use.
Explanation of safety symbols and danger/warning indications.
Description of electronic management, sensors, and advanced components.
Details on operating range, compressors, fans, and construction.
Information on R-410A refrigerant and disposal.
List of available separate accessories for system integration.
Overview of the USER INTERFACE and TERMINAL BLOCK for plant management.
Diagram illustrating system configuration with KCTR for radiant and fan coil.
Performance data for heating capacity and COP for radiant panel use.
Performance data for heating capacity and COP for fan coil use.
Power consumption, supply voltage, and current ratings.
Physical dimensions and weight of the unit.
Description of information shown on the main display screen.
Description of key functions: short pressure, prolonged pressure, menu navigation.
Procedure for setting the date and time on the user interface.
Procedure for setting the password to access parameters.
Overview of parameters organized into sub-menus like HP, SEns, di, etc.
Configuration of climatic curve parameters for system operation.
Settings for inverter frequency modulation and control.
Parameters for managing low-temperature valves in radiant systems.
Configuration of antifreeze protection parameters.
Settings for time bands P1, P2, and daily assignments (dAYS).
Control of heat pump ON/OFF status via external contact or USER INTERFACE.
Automatic setting of heat pump start-up and switch-off times.
Automatic activation of Pump 1 by USER INTERFACE or external commands.
Usage of Pump 2 for high and low temperature systems.
Methods to change the heat pump's operating mode.
Parameters and logic for winter heating temperature curves.
Parameters and logic for summer cooling temperature curves.
Climatic curves for fan coil operation when Set Point 2 is active.
Explanation of safety symbols and danger/warning indications.
Precautions for safe operation and handling of the unit.
Critical safety information before commencing installation.
Warnings about heavy weight, gas leakage, and electrical hazards during installation.
Detailed dimensions and required clearances for THAITY 105.
Detailed dimensions and required clearances for THAITY 110.
Detailed dimensions and required clearances for THAITY 116.
Recommendations for unit placement, noise, wind, and safety precautions.
Diagram identifying key components of the THAITY 105 unit.
Diagram identifying key components of the THAITY 110 unit.
Diagram identifying key components of the THAITY 116 unit.
Performance curves showing capacity and pressure for THAIY 105.
Performance curves showing capacity and pressure for THAIY 110.
Performance curves showing capacity and pressure for THAIY 116.
Guidelines for connecting hydraulic circuits, including pipe sizing and insulation.
Table showing glycol concentration effects on freezing temperature and performance.
Critical safety warnings regarding electrical shock hazards and proper installation.
Items to check before system operation to ensure proper installation.
Steps for testing the system after installation.
Post-installation checks, including refrigerant leak detection and system operation.
Safety warnings for maintenance and proper cleaning procedures.
Tips for efficient operation of cooling and heating modes.
Procedure for checking condensate drainage in winter operation.
Important checks to perform before requesting service.
List of alarm codes displayed on the USER INTERFACE and their causes/solutions.
Procedure for viewing and deleting error logs from the PCB display.
How to navigate and view system data on the display.
Detailed wiring diagram for the THAITY 105 model.
Detailed wiring diagram for the THAITY 110 model.
Detailed wiring diagram for the THAITY 116 model.
French wiring diagram for the THAITY 105 model.
French wiring diagram for the THAITY 110 model.
French wiring diagram for the THAITY 116 model.
German wiring diagram for the THAITY 105 model.
German wiring diagram for the THAITY 110 model.
German wiring diagram for the THAITY 116 model.
Spanish wiring diagram for the THAITY 105 model.
Spanish wiring diagram for the THAITY 110 model.
Spanish wiring diagram for the THAITY 116 model.
Configuration and management of the mixing valve for radiant systems.
Configuration of parameters within the 'Set' menu.
Temperature limits for the first set point in radiant systems.
Management of overheating (Surr) and condensation (Cond) alarms.
Configuration and management of the mixing valve for radiant systems.
Configuration of P3-4 parameter for water supply system temperature.
Configuration of parameters within the 'Prg' menu.
Management of overheating (Surr) and condensation (Cond) alarms.
Configuration and management of the mixing valve for radiant systems.
Configuration of the P3-4 parameter for water supply system temperature.
Configuration of parameters within the 'Prg' menu.
Temperature limits for the first set point in radiant systems.
Management of overheating (Surr) and condensation (Cond) alarms.
Configuration and management of the mixing valve for radiant systems.
Configuration of the P3-4 parameter for water supply system temperature.
Configuration of parameters within the 'Prg' menu.
Temperature limits for the first set point in radiant systems.
Management of overheating (Surr) and condensation (Cond) alarms.
Configuration and management of the mixing valve for radiant systems.
Configuration of the P3-4 parameter for water supply system temperature.
Configuration of parameters within the 'Prg' menu.
Temperature limits for the first set point in radiant systems.
Management of overheating (Surr) and condensation (Cond) alarms.
General