Riello UPS Sentinel Tower STW 6000

Questions and Answers

Y
ybriggsDec 1, 2025
Why won't my Riello UPS Power distribution unit switch to standby mode?
- T
  Teresa ParkerDec 1, 2025
  If your Riello UPS Power distribution unit is connected to the mains but doesn't switch to standby mode (the display doesn't light up), several issues could be the cause: * A missing connection to the input terminal: Connect the mains to the terminals following the instructions in the “POWER CONNECTION” section. * A missing neutral connection: The UPS requires a neutral connection to function. Connect the mains to the terminals as explained in the “POWER CONNECTION” section. Note: the absence of this connection can damage the UPS and/or the load. * The isolator (SWIN) is open: Close the isolator. * Mains power is missing (blackout): Ensure the mains power is present. If necessary, perform a battery start-up to power the load. * The upstream protection device has been triggered: ...
A
Andrea FinleyAug 25, 2025
What does it mean if my Riello UPS Power distribution unit display shows F37 or L37?
- J
  John MarshallAug 26, 2025
  If your Riello UPS Power distribution unit display shows one or more of the following codes: F37, L37, it could be due to several factors: * Ambient temperature exceeding 40°C. * Heat sources positioned too close to the UPS. * Obstructed ventilation slits or proximity to walls. * A fault within the temperature probe or in the battery charger cooling system. To address this, eliminate the cause of the overtemperature. Activate the maintenance bypass (SWMB) if present, open the battery fuse holder isolators (SWBATT), and allow the battery charger heat sink to cool down. Then, close the battery fuse holders. If the problem continues, contact your nearest service center. Warning: Never open the SWBATT fuse holder isolators during battery operation.
J
Joseph HarringtonAug 27, 2025
What does it mean if my Riello UPS Power distribution unit shows codes F03, F04, F05, A08, A09, or A10?
- M
  Michael SullivanAug 27, 2025
  If your Riello UPS Power distribution unit display shows one or more of the following codes: F03, F04, F05, A08, A09, A10, check the connection on the phases, ensuring that with the three-phase connection the switch is in the “? 3~” position and that Phase 2 and Phase 3 are correctly connected. If you are using a single-phase connection, make sure the switch is in the “? 1~” position. If the issue persists, it is possible that the internal protection fuses on the phase or on the input relay are broken, and you should contact the nearest service centre.
R
rwilliamsAug 27, 2025
What to do if my Riello UPS Sentinel Tower STW 6000 Power distribution unit display shows code A26?
- R
  Rhonda EricksonAug 27, 2025
  If the Riello UPS Power distribution unit display shows the code A26, it indicates that the battery fuses are blown or the fuse holder isolators are open. Replace the fuses or close the battery fuse holder isolator (SWBATT). If necessary, replace the fuses with others of the same type.
M
mariabentonAug 30, 2025
What to do if my Riello UPS Sentinel Tower STW 6000 Power distribution unit has no power to the load?
- S
  Sara DouglasAug 30, 2025
  If no power reaches the load from your Riello UPS Power distribution unit, it might be due to a few reasons: * A missing connection to the output terminal: Connect the load to the terminals. * The UPS is in standby mode: Run the start-up sequence. * The STAND-BY OFF mode is selected: Change the operating mode, as this mode only powers the loads during a blackout. * A malfunction of the UPS with the automatic bypass out of use: Insert the maintenance bypass (SWMB) and contact the nearest service centre.
A
Andrew HigginsSep 23, 2025
What does it mean if my Riello UPS Sentinel Tower STW 6000 Power distribution unit display and fans are off but the load is powered?
- L
  Laura SmithSep 23, 2025
  If the display is off, the fans are off, but the load is powered on your Riello UPS Power distribution unit, it indicates a fault in the auxiliary power supplies, with the UPS in bypass supported by the redundant power supply. Activate the maintenance bypass (SWMB) if present. Switch off the UPS, wait for a minute, and turn the UPS back on. If the display does not turn on or if the sequence fails, contact the nearest service centre, leaving the UPS in manual bypass mode.
B
Bethany GreerSep 17, 2025
What to do if my Riello UPS Sentinel Tower STW 6000 Power distribution unit display shows the code L11?
- T
  Tina OwenSep 18, 2025
  If the Riello UPS Power distribution unit display shows the code L11, it indicates a static bypass rupture or fault. Activate the maintenance bypass (SWMB) if present, turn the UPS off and back on again, and exclude the maintenance bypass. If the problem persists, contact the nearest service centre.
K
krystalrussellSep 18, 2025
What to do if my Riello UPS Power distribution unit display is not working properly?
- R
  richard07Sep 18, 2025
  If the display of your Riello UPS Power distribution unit shows nothing or provides incorrect information, it indicates that the display has power supply problems. Activate the maintenance bypass (SWMB), shut down the UPS completely, and wait for a few seconds. Turn ON the UPS again and verify display regular operation. Exclude the maintenance bypass. If the fault persists, contact the nearest technical support centre.
R
Rhonda DixonSep 9, 2025
What to do if my Riello UPS Sentinel Tower STW 6000 Power distribution unit display shows code C01?
- E
  Eric ThompsonSep 9, 2025
  If the Riello UPS Power distribution unit display shows the following code: C01, it means that the jumper is missing from the R.E.P.O. connector or it is not inserted correctly. Assemble the jumper or make sure that it is inserted correctly.
B
Brittany HarveySep 6, 2025
What does it mean if my Riello UPS Sentinel Tower STW 6000 Power distribution unit display shows code A13?
- D
  David LewisSep 6, 2025
  If the Riello UPS Power distribution unit display shows the code A13, the issue is due to the protection device upstream from the bypass line being open (only if the bypass is separate) or the bypass isolator being open (SWBYP only if the bypass is separate). Restore the protection device upstream, ensuring there is no overload or short circuit at the output of the UPS. Also, close the isolator.