Assembly instructions
Valdivia
Order No.
1140
Stage 20, the cabin
Part Description Material Dimensions No. Note
No. off
20.1 R.H. inside side panel Spruce Veneer 1 Sheet F, FS
20.2 R.H. outside side panel Spruce Veneer 1 Sheet F, FS
20.3 L.H. inside side panel Spruce Veneer 1 Sheet F, FS
20.4 L.H. outside side panel Spruce Veneer 1 Sheet F, FS
20.5 Inside front panel Spruce Veneer 1 Sheet F, FS
20.6 Outside front panel Spruce Veneer 1 Sheet F, FS
20.7 Inside rear panel Spruce Veneer 1 Sheet F, FS
20.8 Outside rear panel Spruce Veneer 1 Sheet F, FS
20.9 Cabin housing PVC Vac. 1 Clear
20.10 In-fill piece Spruce 2 x 7 7 Oversize
20.11 Corner piece Spruce 5 x 5 x 25 4
20.12 Roof planking Spruce 3 x 7 x 140 8
20.13 Outer roof planking Spruce 3 x 10 x 140 2
20.14 Roof planking Spruce 3 x 10 x 180 6
20.15 Edging strip Spruce 1.2 x 5 x 140 2
20.16 Hatch rail Spruce 2 x 5 x 70 2
20.17 Loose bulkhead rail Spruce 2 x 2 x 25 2 Oversize
20.18 Loose bulkhead Spruce Veneer 2 Sheet F, FS
20.19 Handrail Plywood, ready made 2 x 45 1 Sheet E, FS
20.20 Handrail Plywood, ready made 2 x 95 1 Sheet E, FS
20.21 Porthole Brass 12 Ø 2 FS
20.22 Lifebelt holder Plywood, ready made 2 3 Sheet E, FS
20.23 Lifebelt Plastic 34 Ø 1 FS
roof, offset one strake’s width to the left of centre. Place
the hatch (17.17) against the first rail as a guide, then glue
the second rail to the cabin roof.
- Cut the recess for the loose bulkhead, and glue the rails
20.17 and the loose bulkhead 20.18 to the structure.
- Glue the handrails 20.19 and 20.20 to the structure as
shown in Figs. 208 and 209.
- The portholes 20.21 have to be sanded back to a thickn-
ess of 1.8 mm. This is done by pushing the porthole firmly
onto the cap of an old cyano bottle to act as a support.
Shorten the cap as shown and sand the porthole down to
the correct depth - Fig. 210.
- Glue the prepared portholes to the cabin - Fig. 211.
- Glue the lifebelt holders 20.22 to the roof using the lifebelt
20.23 as a guide for correct spacing - Fig. 212.
20
- Glue the panels 20.1 to 20.8 to the moulded cabin housing
20.9 - Fig. 205 (housing not shown).
- Trim the length of the in-fill pieces 20.10 so that the gap is
the same width all round; Figs. 206 and 207.
- Attach the corner pieces 20.11.
- Note: the overhang of the cabin roof over the corner pie-
ces should be 2 mm all round.
- Glue four roof strakes 20.12 on each side of the centreline,
starting at the centre.
- Glue the outer strakes 20.13 in place.
- The remaining gaps are filled with three tapered strakes
20.14 on each side. The strakes have to be tapered from 8
to 4 mm.
- Glue the edging strips 20.15 in place.
- Glue the inner rail 20.16 for the sliding hatch to the cabin
Stage 21, the command stand
Part Description Material Dimensions No. Note
No. off
21.1 Command stand housing PVC Vac. 1 Clear
21.2 Side panel Spruce Veneer 2 Sheet F, FS
21.3 Rear side panel Spruce Veneer 2 Sheet F, FS
21.4 Top side panel Spruce Veneer 2 Sheet F, FS
21.5 Front panel Spruce Veneer 1 Sheet F, FS
21.6 Top front panel Spruce Veneer 1 Sheet F, FS
21.7 Side rear panel Spruce Veneer 2 Sheet F, FS
21.8 Back panel Spruce Veneer 1 Sheet F, FS
21.9 Top back panel Spruce Veneer 1 Sheet F, FS
21.10 Corner piece Spruce 5 x 5 x 20 6
21.11 Corner piece Spruce 3 x 5 x 20 4
21.12 Bank padding Spruce 3 x 7 x 70 6
21.13 Centre padding Spruce 3 x 5 x 35 5
To Next Page
Loading...
