33
EN
device.
This installaon manual is intended for qualied personnel only.
ROGER TECHNOLOGY cannot be held responsible for any damage or injury due to improper use or any use other the intended usage indicated in this
manual.
Installaon, electrical connecons and adjustments must be performed by qualied personnel, in accordance with best pracces and in compliance
with applicable regulaons.
Read the instrucons carefully before installing the product. Bad installaon could be dangerous.
Before installing the product, make sure it is in perfect condion: if in doubt, do not use the equipment and contact qualied personnel only.
Do not install the product in explosive areas and atmospheres: the presence of inammable gas or fumes represents a serious safety hazard.
Before installing the motorisaon device, make all the necessary structural modicaons to create safety clearance and to guard or isolate all the
crushing, shearing, trapping and general hazardous areas.
Make sure the exisng structure is up to standard in terms of strength and stability.
ROGER TECHNOLOGY is not responsible for failure to observe Good Working Methods when building the frames to be motorised, or for any
deformaon during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed taking into account: applicable laws and direcves, Good
Working Methods, installaon premises, system operang logic and the forces developed by the motorised door or gate.
The safety devices must protect against crushing, cung, trapping and general danger areas of the motorised door or gate.
ROGER TECHNOLOGY declines all responsibility if component parts not compable with safe and correct operaon are ed.
Display the signs required by law to idenfy hazardous areas.
Each installaon must bear a visible indicaon of the data idenfying the motorised door or gate.
An omnipolar disconnecon switch with a contact opening distance of at least 3mm must be ed on the mains supply.
Make sure that upline from the mains power supply there is a residual current circuit breaker that trips at no more than 0.03A and overcurrent cutout
upstream of the electrical system in accordance with best pracces and in compliance with applicable regulaons.
When requested, connect the automaon to an eecve earthing system that complies with current safety standards.
During installaon, maintenance and repair operaons, cut o the power supply before opening the cover to access the electrical parts.
The electronic parts must be handled using earthed anstac conducve arms.
Only use original spare parts for repairing or replacing products.
The installer must supply all informaon concerning the automac, manual and emergency operaon of the motorised door or gate, and must
provide the user with the operang instrucons.
The packaging materials (plasc, polystyrene, etc.) should not be discarded in the environment or le within reach of children, as they are a potenal
source of danger.
Dispose of and recycle the packing components in accordance with the standards in force.
These instrucon must be kept and forwarded to all possible future user of the system.
I the undersigned, as acng legal representave of the manufacturer:
hereby DECLARE that the appliance described hereaer:
Descripon: Swing gate automaon
Model: serie SMARTY
Is conformant with the legal requisites of the following direcves:
• Direcve 2014/30/EU (EMC Direcve) and subsequent amendments;
• Direcve 2014/35/EU (Low Voltage Direcve) and subsequent amendments;
and that all the standards and/or technical requirements indicated as follows have been applied:
Last two gures of year in which marking was applied | 16.
Place: Mogliano V.to Date: 30/04/2016 Signature
ROGER TECHNOLOGY is the exclusive proprietor holder of all rights regarding this publicaon.
ROGER TECHNOLOGY reserves the right to implement any modicaons without prior nocaon. Copying, scanning or any alteraons to this document are prohibited
without express prior authorised from by ROGER TECHNOLOGY.
This instrucon manual and the warnings for the installer are given in printed form and included in the box containing the product.
The digital version of this documentaon (in PDF format) and all future revisions are available from the reserved area of our website www.rogertechnology.com/B2B,
in the secon ‘Self Service’.
ROGER TECHNOLOGY CUSTOMER SERVICE:
business hours: Monday to Friday 08:00 to 12:00 - 13:30 to 17:30
Telephone no: +39 041 5937023
E-mail: service@rogertechnology.it
Skype: service_rogertechnology
To Next Page
Loading...
Need help?
General
