Rohde & Schwarz URV5-Z4 - Probe Insertion and Data Handling

2.3.2
Probes
The
probes
are
inserted
into
the
openings
1g
(A
or
B)
together
with-the
plug-in
adapters.
Correct
insertion
of
the
probes
is
re-
cognized
by
the
URVS
both
in
manual
and
in
remote
control
mode,
but
it
is
recommended
to
insert
the
probes
in
manual
mode
only.
In
remote
mode,
with
correspondingly
adjusted
interface
(01
to
Q3),
the
URVS
only
sends
SRQ
(114)
to
the
controller
in
order
to
avoid
any
interruption
of
the
current
program.
(When removing the probe in the main measurement channel: SRQ
(104)
and
abortion
of
measurement).
'
-
The
probe
data
for
evaluation
in
the
instrument
are
read
in
imme-
diately
in
local
node,
whereas
in
remote
node
they
are
read
in
only
after
the
command
C0
has
been
sent
to
the
URVS
or
after
switching
to
local
mode.
The
type
of
probe
(DC/AC
probe,
RF
probe
etc.)
and
further
probe-
specific
data
such
as
frequency
response,
calibration
and
atte-
nuation
factors
(e.g.
for
1oo-v
insertion
unit)
are
thus
known
to
the
instrument
and
will
be
considered
for
the
operation
and
eva-
luation
of
the
corresponding
channel.
After
the
data
have
been
read
in,
the
URVS
is
immediately
ready
for
measurements.
Note:
For
complete
technical
data
and
specifications
please
refer
to
the
URVS
data
sheet.
The
values
cited
in
the
manual
are
intended
as
guide-
lines
for
the
user
and
can
under
circumstances
differ
from
those
of
the
data
sheet.
Rt
Imeasurement
range)
Vin: 0 to 400 V
vIn
—o
.
.
l
9nn
_
R1“.
9
MR
:[6pp shunted by
6p?
Probe
db
Bask on"
Pig.
2-3
Equivalent
circuit
diagram
of
DC
probe
394.8010.02
2.9
3-2
2.3.2
probes
The probes
are inserted into the openings 18 (A er
B)
tog.ether
witz the plug-in adapters. Correct InsertioN-Of the probes ıs re-
cognized by the URV5 both in manual and in remote control
mode,
but it is recommended to insert the probes in manual Mode only.
In remote mode, Voith correspondingly adjusted interf ace (01 to
Q3), the URV5 only sends SRQ (114) to ~the Controller in Order to
avoid any interruption of the current programm.
(When
(-104)
removing the probe in the main
and abortion of measurement) .
measurement Channel: SRO
The probe data for evaluation in the Instrument are read in imme-
diately in local Mode, whereas in remote Mode they. are read in
only after the Command cm has been seht to the URV5 er af ter
switching to local mode.
The type of probe (DC/AC probe, RF probe etc. J and fur ther probe-
specific data such as frequency response, calibration and atte-
nuation factors (e.g. for 100-V Insertion Unit) are thus knoten to
the Instrument and will be considered for the Operation and eva-
luation of the
corresponding Channel. After the data have been
read in, the URV5 is immediately ready for measurements.
Note:
data and specifications please
sheet.
For complete technical
refer to the URV5 data
The Values cited in the manual are intended as guide-
lines for the User and can under circumstances dıffer
fror those of the data sheets.
2.3 .2~. 1
DC Probe
vın
u
l
T
6pF
Probe
9H0
!
l
I
U
ı
I
I
l
Rc (measurement range!
I I
U
Basic Unit
Von: 0 to 400 V
Ring
9
mn
shunted
6pF
bi
Fig. 2-3 Equivalent circuit diagramm of DC probe
394.8010.02
2.9
E-2