11
Roland GW-7 MIDI Implementation
■Parameter Address Map
●Common parameters (Model ID=42H)
The parameters common to all Parts in each module are called Common parameters.
Address (H) Size (H) Data (H) Parameter Description Default Value (H) Description
40 00 00 00 00 04 0018 - 07E8 MASTER TUNE -100.0 - +100.0 [cents] 00 04 00 00 0 [cents]
40 00 01# Use nibblized data.
40 00 02#
40 00 03#
* Refer to “5. Supplementary material”, About the Tuning (p. 19).
Address (H)
Size (H) Data (H) Parameter Description Default Value (H) Description
40 00 04 00 00 01 00 - 7F MASTER VOLUME 0 - 127 7F 127
(= F0 7F 7F 04 01 00 vv F7)
40 00 05 00 00 01 28 - 58 MASTER KEY-SHIFT -24 - +24 [semitones] 40 0 [semitones]
40 00 06 00 00 01 01 - 7F MASTER PAN -63(LEFT)- +63(RIGHT) 40 0(CENTER)
40 00 7F 00 00 01 00 MODE SET 00 = GS Reset
(Rx. only)
40 01 30 00 00 01 00 - 07 REVERB MACRO 00: Room 1 04 Hall 2
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05: Plate
06: Delay
07: Panning Delay
40 01 31 00 00 01 00 - 07 REVERB CHARACTER 0 - 7 04 4
40 01 32 00 00 01 00 - 07 REVERB PRE-LPF 0 - 7 00 0
40 01 33 00 00 01 00 - 7F REVERB LEVEL 0 - 127 40 64
40 01 34 00 00 01 00 - 7F REVERB TIME 0 - 127 40 64
40 01 35 00 00 01 00 - 7F REVERB DELAY FEEDBACK 0 - 127 00 0
40 01 37 00 00 01 00 - 7F REVERB PREDELAY TIME 0 - 127[ms] 00 0
* REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverb parameter will be set to their most
suitable value.
* REVERB CHARACTER is a parameter that changes the reverb algorithm. The value of REVERB CHARACTER corresponds to the REVERB MACRO of the same number.
Address (H) Size (H) Data (H) Parameter Description Default Value (H) Description
40 01 38 00 00 01 00 - 07 CHORUS MACRO 00: Chorus 1 02 Chorus 3
01: Chorus 2
02: Chorus 3
03: Chorus 4
04: Feedback Chorus
05: Flanger
06: Short Delay
07: Short Delay(FB)
40 01 39 00 00 01 00 - 07 CHORUS PRE-LPF 0-7 00 0
40 01 3A 00 00 01 00 - 7F CHORUS LEVEL 0-127 40 64
40 01 3B 00 00 01 00 - 7F CHORUS FEEDBACK 0-127 08 8
40 01 3C 00 00 01 00 - 7F CHORUS DELAY 0-127 50 80
40 01 3D 00 00 01 00 - 7F CHORUS RATE 0-127 03 3
40 01 3E 00 00 01 00 - 7F CHORUS DEPTH 0-127 13 19
40 01 3F 00 00 01 00 - 7F CHORUS SEND LEVEL TO REVERB 0-127 00 0
* CHORUS MACRO is a macro parameter that allows global setting of chorus parameters. When you select the chorus type with CHORUS MACRO, each Chorus parameter will be set to their
most suitable value.
Address (H) Size (H) Data (H) Parameter Description Default Value (H) Description
40 03 17 00 00 01 00 - 7F MFX SEND LEVEL TO REVERB 0-127 28 40
* MFX TYPE is a macro parameter which sets various Insertion Effect parameters as a group. When you use MFX TYPE to select an Insertion Effect type, each effect parameter will be set to the
most suitable value.
To Next Page
Loading...
