Roland JUNO-D Midi Implementation

7
❍ Expression (Controller number 11)
Status
2nd byte 3rd byte
BnH 0BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Expression: 00H - 7FH (0 - 127)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to EXPRESSION.
❍ Effect Control 1 (Controller number 12)
Status
2nd byte 3rd byte
BnH 0CH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value (relative change): 0H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to MFX PARAMETER1.
❍ Effect Control 2 (Controller number 13)
Status
2nd byte 3rd byte
BnH 0DH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to MFX PARAMETER2.
❍ Hold 1 (Controller number 64)
Status
2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
❍ Portamento (Controller number 65)
Status
2nd byte 3rd byte
BnH 41H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to PORTAMENTO.
❍ Sostenuto (Controller number 66)
Status
2nd byte 3rd byte
BnH 42H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to SOSTENUTO.
❍ Soft (Controller number 67)
Status 2nd byte 3rd byte
BnH 43H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to SOFT.
❍ Resonance (Controller number 71)
Status
2nd byte 3rd byte
BnH 47H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv= Resonance value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to RESONANCE.
❍ Release Time (Controller number 72)
Status
2nd byte 3rd byte
BnH 48H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to RELEASE TIME.
❍ Attack time (Controller number 73)
Status
2nd byte 3rd byte
BnH 49H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to ATTACK TIME.
❍ Cutoff (Controller number 74)
Status 2nd byte 3rd byte
BnH 4AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Cutoff value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to CUTOFF.
❍ Decay Time (Controller number 75)
Status
2nd byte 3rd byte
BnH 4BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Decay Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to DECAY TIME.
❍ Vibrato Rate (Controller number 76)
Status 2nd byte 3rd byte
BnH 4CH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Rate value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to LFO RATE.
❍ Vibrato Depth (Controller number 77)
Status 2nd byte 3rd byte
BnH 4DH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Depth Value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to LFO DEPTH.
❍ Vibrato Delay (Controller number 78)
Status
2nd byte 3rd byte
BnH 4EH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Delay value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to LFO DELAY.
❍ Effect 1 (Reverb Send Level) (Controller number 91)
Status
2nd byte 3rd byte
BnH 5BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Reverb Send Level: 00H - 7FH (0 - 127)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to REV SEND LEVEL.
❍ Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte 3rd byte
BnH 5DH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Chorus Send Level: 00H - 7FH (0 - 127)
* Sent when the Modulation/Pedal/C1-C3 Assign parameter (SYSTEM CONTROLLER) is
set to CHO SEND LEVEL.

Roland JUNO-D Specifications

General

Type	Digital Synthesizer
Polyphony	64 voices
Preset Performances	32
Arpeggiator	Yes
Rhythm Guide	Yes
MIDI	Yes
Effects	Reverb, Chorus
Keyboard	61 keys (velocity-sensitive)
Controllers	Pitch Bend/Modulation Lever
Connectors	Output (L/Mono, R), Headphones, MIDI (In, Out)
Power Supply	DC 9V
Waveforms	PCM
USB	Yes
User Patches	128 patches
Oscillators	Not specified in detail, uses PCM waveforms