Roland JV-880 - Page 220

O
Effecti
depth(Reverb
send level)
Status
BnH
Second
5BH
Third
vvH
n
=
MIDI
channel number
; OH
-
FH { ch.l
-
ch.l6
)
vv
=
Control
value
:00H-7FH
(0-127)
0-63
=
OFF
64-127=
ON
*
In the
patch mode, switched over the reverb switch of the
system common.
*
In the
performance mode,
switched
over
the
reverb switch of the
performance
part.
And
specified the control
channel,
switched over
the
reverb switch
of the system
common.
*
Ignore
when "Control change" of the
system
common is
OFF.
O
Effects
depth(Chorus send level)
Status
BnH
Sggopd
SDH
Third
vvH
n
=
MIDI channel number : OH
-
FH {
-
15
)
=
ch.l 15
=
ch.l6
vv
=
Control
value
:00H-7FH
(0-127)
0-63
=
OFF
64-127=
ON
*
In the
patch
mode, switched over the chorus
switch
of the system common.
*
In the
performance mode, switched
over
the
chorus switch of
the
performance
part.
And
specified the control channel, switched
over
the chorus switch of the
system
common.
*
Ignored
when
"Control change" of the
system common is
OFF.
Orpnlsb
Status
$econd
Third
BnH
64H
IIH
n
=
MIDI
channel number : OH
-
FH
(
ch.l
-
ch.l6
)
11
=
LSB of the
specified parameter by RPN
Orpnmsb
Status
Second Third
BnH 65H
mmH
n
=
MIDI
chuannel number : OH
-
FH
(ch.l
-
ch.l6
)
mm
=
MSB of the
specified
papameter
by
RPN
O
Data
entry LSB
Status
BnH
Second
26H
Third
UH
n
=
MIDI
channel number
: OH
-
FH
(
ch.l
-
ch.l6
)
11
=
Value of the
parameter
specified with RPN
*
Ignored
when "Control
change" of
the system common
is
OFF.
O
Data
entry MSB
Status
BnH
Second
06
H
n
=
MIDI
channel number
: OH
-
FH
(
ch.l
-
ch.l6
)
mm
=
Value of the
parameter
specified
with RPN
*
Ignored when "Control
change"
of the system
common is OFF.
* *
RPN
*
*
RPN (registered
parameter
number)
is
a
parameter
number of tone color or
musical expression
defined
in MIDI
specification.
With
the
JV-880
as the
receiver, RPN #0
(pintch bend
sensitivity), RPN
#
1
(fine tuning) and RPN #
2
(coarse tuning)
are effective.
When sending an
RPN to the
JV
-
880,
first
specify the MSB
and LSB of the RPN to be used
to
control
a
parameter
and then set
the
value in the data
entry field.
BnH
6SH mU
(
RPN MSB
)
BnH 64H UH
(
RPN LSB
)
BnH
06H
xxH BnH
26H
yyH
(
Data
Entry MSB
)
( Data Entry LSB
)
n
=
MIDI channel number :
OH
-
FH (
ch.l
-
ch.l6
)
RPN Data
entry Description
im LSB MSB LSB
wm 11 XX
yy
OOH OOH xxH
—
Pitch bend sensitivity
XX
: OOH
-
OCH (
-
12 semi
tone)
yy
: Ignored
(Up to
1 octabe)
•You
can adjust
"Bend
range
up"
and
"Bend range
down" at
same time.
*In the rhythm
part(part8),
this
oessaage is not
recognized.
OOH GIH xxH
yyH
OOH
02H
xxH
Fine tuning
XX.
yy
: 20H, OOH
-
40H, OOH
-
60H, OOH
(-50
-
-
+50
cent
)
*In the patch mode, adjusted the master
tune.
*In the
performance mode,
adjusted
fine
tune at each part.
*In the
performance
mode,
specified
control channel, changed
the master
tune.
Coarse tuning
XX : lOH
-
40H
-
70H
(-48
-
-
+48 semitone)
yy
: Ignored
*In
the patch mode, this iMSsaage is not
recognized.
*In the
performance mode,
adjusted
coarse tune at each part.
RPN
reset
XX,
yy
: Ignored
•Return to
no specified
parameter of RPN.
Current setting value is no change.
*
Either MSB or LSB of the RPN
can be sent first: no
problem with
the
JV-J
*
In contrast, data must
be entered MSB first followed
by
the LSB.
(The
JV
—
880 clears the existing
LSB to
"0"
as
it receives
the
MSB.)
7FH 7FH
I
Program change
Status
CnH
Second
PPH
n
=
MIDI channel number
pp
=
Program
number
: OH
-
FH ( ch.l
-
ch.l6
)
: OOH
-
7FH (
-
127
)
*
Ignored when
"Program change" of the
system
common is
OFF.
*
When the
JV
—
880
receives
a program change on
a part
receive
channel while
in the performance mode, it
changes the patches
of
that part : the new patch
value
being the program number
plus 1. If the
JV
—
880 receives the program
change on the control channel, it
changes the performance according to the
table below.
CnH ppH Performance
(Bank select
SOfBank select
=
811)
OOH
OIH
OFH
lOH
101
[
AOl
]
102
[
A02
]
116
[
A16
]
101
[
AOl
]
•Even
if program
changes cover from
lOH to 3FH,
the
JV-880
only
repeats I01(A01)-I16(A16).
3FH
116
[
A16
]
40H €01
[
BOl
]
41H C02
[
B02
]
4FH 016
[
B16
]
50H COl
[
BOl
]
7FH
•Even if program
changes cover from
50H to 7FH,
the
JV-880
only
repeats C01(B01)-C16(B16).
C16
[
B16
]