Roland R-26 User Manual (English)

Other manuals for Roland R-26

Owner's Manual112 pages

Brochure & Specs2 pages

Quick Start Guide10 pages

Questions and Answers:

D
Denise MartinezAug 22, 2025
Why can't I record with my Roland R-26?
- B
  Bradley HaydenAug 22, 2025
  If you can't record with your Roland Recording Equipment, there could be several reasons: * The SD card might not be inserted correctly. Turn off the power and re-insert the SD card. * The SD card might not be formatted. Format the SD card. * The SD card might have been formatted incorrectly using a computer. The card should be formatted on the R-26. * The SD card might be write-protected. Turn off write protection. * The recording level might be too low. Set the recording level appropriately.
J
Jason NelsonAug 25, 2025
Why is there no sound coming from my Roland R-26 Recording Equipment?
- E
  Elizabeth MortonAug 25, 2025
  If you're experiencing no sound with your Roland Recording Equipment, the issue might be due to the output volume being too low. Try gradually increasing the output volume. Also, verify that your headphones or speakers are correctly connected.
E
Edward HaasAug 25, 2025
What to do if my Roland Recording Equipment power won’t turn on?
- J
  John BenitezAug 26, 2025
  If your Roland Recording Equipment won’t turn on, check the following: 1. Make sure that the AC adapter is connected correctly. 2. If using batteries, ensure they are oriented correctly and fit well in the compartment. 3. If the batteries are low, replace them with fresh ones.
E
Emily StaffordAug 27, 2025
How to fix distorted sound on my Roland Recording Equipment?
- M
  Matthew WatsonAug 27, 2025
  If the recorded sound from your Roland Recording Equipment is distorted, it's likely that the input level or input sensitivity is too high. Adjust the recording level appropriately to resolve this.
D
Daniel BrownAug 27, 2025
What to do if my Roland R-26 can’t play back files?
- R
  Ryan HeathAug 27, 2025
  If you can't play back files on your Roland Recording Equipment, consider these points: * Ensure the file name is correctly assigned; the R-26 cannot use files that begin with a period (“.”). * Make sure the file extension is either .MP3 or .WAV, as the R-26 only supports these formats. * If the file is damaged, attempt to recover it using the Repair function. * When using the unit as an audio interface, ensure the project's sampling frequency matches the audio interface's set sampling frequency.
E
emily95Aug 28, 2025
Why does my Roland R-26 Recording Equipment power turn off unexpectedly?
- D
  Dr. Terry JenkinsAug 29, 2025
  If your Roland Recording Equipment turns off unexpectedly, it could be due to the Auto Off setting; check this setting. Also, verify the end voltage setting is appropriate. If you're using batteries, they may be running low, so install fresh batteries.
J
jon55Aug 29, 2025
Why is there no sound from my condenser mic on my Roland R-26 Recording Equipment?
- D
  David YangAug 30, 2025
  If you're not receiving sound from a condenser mic connected to your Roland Recording Equipment, ensure that phantom power is turned on. Condenser mics require phantom power to function.
T
Taylor CampbellAug 31, 2025
Why is my plug-in mic not working with my Roland R-26 Recording Equipment?
- M
  Molly KennedyAug 31, 2025
  If you're not getting any sound from your plug-in mic with your Roland Recording Equipment, make sure that plug-in power is turned on.
C
Carlos MackSep 1, 2025
Why can't I start recording on my Roland R-26 Recording Equipment?
- X
  xmendezSep 1, 2025
  If you can’t start recording on your Roland Recording Equipment, it may be because the SD card has less than 16 kilobytes of free space. Ensure the SD card has enough free space.
J
John JonesSep 2, 2025
Why is my Roland Recording Equipment only recording on the left channel?
- S
  Samuel MaynardSep 2, 2025
  If the sound recorded from the mic is only heard from the left channel on your Roland Recording Equipment, and you're using a monaural mic, this is normal. To record onto both channels, use the “MIC TYPE” screen to set the external mic type to “MONO.”