Roland STUDIO M User Manual

-
lmportant
Notes
1. Power Supply
&When
using
an AC adaptor,
be
sure that
it is
one supplied
by the manufacturer. Use of any
other
power
adaptor
could result in damage,
malfunction,
or electric shock.
&When
making
any connections
with
other
devices,
always turn
off the
power
to all
equipment
first; this
will help
prevent
damage
or
malfunction.
&Do
not use this
unit on the same
power
circuit
with any device
that will
generate
line noise,
such
as a motor or
variable lighting system.
&Please
use the AC
Adaptor of appropriate
voltage
(12o,22O,
or 24o) depending on
the
voltage system
in
your
contury.
&Avoid
damaging
the
power
cord; do not step
on
it,
place
heavy objects
on
it
etc.
&When
disconnecting
the
AC adaptor from the
outlet,
grasp
the
plug
itself;
never
pull
on the
cord.
&lf
the unit is
to remain unused
for a long
period
of time, unplug
the
power
cord.
2.
Placement
&Do
not subject the
unit
to temperature
extremes
(eg.
direct sunlight
in an enclosed
vehicle).
Avoid using
or storing
the unit in
dusty
or
humid areas or
areas that are subject
to
high
vibration levels.
&Using
the unit
near
power
amplifiers
(or
other
equipment
containing
large transformers)
may
induce hum.
&Observe
the following
when using the unit's
disk
drive.
For further
details,
refer to
"Disk
Handling".
-Do
not
place
the
unit near
devices that
produce
a strong
magnetic
field(eg. loud-
speakers).
-lnstall
the unit on a solid,
Ievel surface.
-Do
not move
the unit or subiect
it to vibra-
tion
while it is operating.
&Do
not expose this
unit
to temperature
extremes
(eg.
direct sunlight
in an
enclosed
vehicle can
deform or discolor
the unit)
or
install
it
near devices that
radiate heat.
&lnstall
the unit
on a solid,
level surface
in an
area
free from
vibration.
lf the unit must
be
installed
at an angle,
be sure
that the angle of
installation
falls within the
to lerance
range
(With
stand:
upward;
27 degrees,
downward
13 degrees.
Without stand: upward;
20
degrees,
downward;
20 degrees)
.aa 4
&Avoid
using the drive in areas of high humidity
(eg.
condensation). High levels of moisture
can adversely affect the operation of the drive
and
/or
damage disks.When the unit has
been transpoded, allow it to
warm
to room
temperature before
operating.
@To
inserl a disk,
push
it firmly into the drive.
To remove a
disk,
press
the eject button
firmly.
Do not
use excessive
force to remove
a disk
which is
lodged in the drive.
&Never
remove a disk from the drive while it is
operating; damage
could
result to both the
disk and the
drive.
&Before
powering
up or
powring
down, remove
any disk from the drive.
3.
Maintenance
&For
everyday cleaning
wipe the unit with a
soft,
dry cloth
(or
one that
has been
slightly
dampened
with water). To remove stubborn
dirt, use a mild neutral detergent.
Afterwards,
be sure to wipe the
unit
thoroughly with a soft,
dry
cloth.
&Never
use benzene, thinners, alcohol or sol-
vents of any kind, to avoid the
risk
of disc
oloration
and
/
or deformation.
4. Additional
Precautions
&Protect
the unit from strong
impact.
&A
small
amount
of
noise may be heard from
the display, and thus should
be considered
nomal.
&Do
not allow objects or liquids
of any kind to
penetrate
the unit.
ln
the
event of such an
occurrence, discontinue use
immediately.
Contact
qualified
service
personnel
as soon
as
possible.
&should
a malfunction occur
(or
if
you
suspect
there
is a
problem)
discontinue
use immed
iately. Contact
qualified
service
presonnel
as
soon
as
possible.

Roland STUDIO M Specifications

General

Brand	Roland
Model	STUDIO M
Category	Music Equipment
Language	English