25
Algorithm List
Gate Reverb
This is a reverb in which the reverberation is muted during its decay. Its reverse mode can be used in conjunction with Accent
sounds to obtain sounds like from reverse play back of a tape.
fig.08-42
Parameter (full name) Setting Function
GRev (Gate Reverb): Mutes the revert sound midway.
Sw (Switch) On, Off Turns the gate reverb on or off.
Mode (Gate Mode) See the column on
the previous page. Defines how the reverb sound is applied.
Time (Gate Time) 10–400 s Sets the time from when the reverb sound begins until it is muted.
PreDLY (Pre-Delay) 0–300 ms Sets the time until the reverb sound appears.
Thick (Thickness) 0–100 Sets the thickness of the reverb sound.
Densty (Density) 0–100 Sets the density of the reverb sound.
AcDLY (Accent Delay Time) 0–200 ms Sets the time from when the reverb sound is muted until the accent sound appears.
AcLvl (Accent Level) 0–100 Sets the volume of the accent sound.
AcPan (Accent Pan) L63–R63 Sets the pan of the accent sound.
FX Lvl (Effect Level). -100–100 Sets the volume of the gate reverb sound.
DirLvl (Direct Level) -100–100 Sets the volume of the direct sound.
EQ (Equalizer)
Sw (Switch) On, Off Turns the equalizer on or off.
Low Gain (Low Gain) -12– +12 dB Sets the boost/cut amount in the low frequency band.
Low Freq (Low Frequency) 20 - 2000 Hz Sets the center frequency in the low frequency band.
Low Q 0.3–10.0 Sets the width of the area around the low frequency that will be affected by the gain settings. *1
Low Type Shlv, Peak Sets the type of the low frequency band equalizer (Shlving type or peaking type).
Mid Gain (Middle Gain) -12– +12 dB Sets the boost/cut amount in the middle frequency band.
Mid Freq (Middle Frequency) 200–8000 Hz Sets the center frequency in the middle frequency band.
Mid Q (Middle Q) 0.3–10.0 Sets the width of the area around the middle frequency that will be affected by the gain settings.
High Gain -12– +12 dB Sets the boost/cut amount in the High frequency band.
High Freq (High Frequency) 1.4–20.0 kHz Sets the center frequency in the High frequency band.
High Q 0.3–10.0 Sets the width of the area around the High frequency that will be affected by the gain settings. *1
Hi Type (High Type) Shlv, Peak Sets the type of the High frequency band equalizer (Shlving type or peaking type).
Level (Output Level) 0–100 Sets the volume after passing through the equalizer.
*1: If Low Type (Lo Type) or High Type (Hi Type) is set to “Shlv (Shlving Type),” the setting for Lo Q or High Q is invalid.
* “Gate Reverb” cannot be used on EFFECT2, 4, and 6 (even-numbered effects).
Input L
Input R
Gate Reverb
Output L
Output R
Direct Level
Direct Level
3BAND EQ
3BAND EQ
Gate Reverb
fig.08-43e
Reverb applications
You can select how reverb sounds can be applied by
setting up Gate Mode (Mode).
Normal: Ordinary Gate Reverb
L->R: The Gate Reverb sound moves from the left to
right side.
R->L: The Gate Reverb sound moves from the right to
left side.
Reverse1: Reverse Gate (effect as if reverb are replayed
backward.)
Reverse2: Reverse Gate that causes the reverb sound to
decay midway.
Level
Direct sound (DirLvl)
Time
Pre Delay
(PreDLY)
Gate Time
(Time)
Accent Delay Time
(AcDLY)
Accent
Level
(AcLvl)
Reverb
Level
(EfxLvl)
Reverb sound
Accent sound
VS-2000_e.book 25 ページ ２００５年１２月１２日 月曜日 午後４時５４分
To Next Page
Loading...
