Manually
adjust
the handbrake
caliper
mechanism.
Inspect
all
pipes
and connections.
Rectify
if
necessary.
5.
Fluid
levels:
Check
all
fluid
levels.
6. Torque converter transmission: Check the
fluid
level
and top·up
if
necessary.
When
checking the
fluid
level
avoid
contact
with the exhaust gas
recirculation
valve,
heatshield
and associated pipes as these components
will
be
hot.
Every 20 000 kilometres (12 000 miles) or 12
months
whichever
is
the earlier
1.
Air
injection
pump: Check the tension
of
the
pump
pulley
driving
belt.
2.
Air
silencer:
Fit
a new paper
filter
element.
3.
Carburetters: Top-up the
air
valve
dampers
with
new engine
oil.
Check and
if
necessary
adjust
float
chamber
depression. Check
tightness
of
float
chamber
covers.
Check engine i
die
speed and choke
fast-idle
speed;
adjust
as necessary.
4. Crankcase emission control system: Remove
and clean the gauze flame traps in the crankcase
breather tube. Clean the adapter
in
the choke
butterfly
housing.
5. Engine: Change the engine
oil
and
fit
a new
oil
filter
element.
6. Fuel evaporation emission control system:
Check the
condition
of
the pipes and connections.
7.
Ignition
system:
Fit
new sparking
plugs
ensuring
that
the
gaps are set to 0,9
mm.
(0.035
in.).
Lubricate
distributor
spindle
(shaft
bearings)
and automatic advance mechanism
with
engine
oil.
Check
ignition
timing
with
stroboscope and
adjust
if
necessary.
The
ignition
timing should be
15°
B.T.D.C.
with
the
engine running
at
1 200 r.p.m.,
the vacuum
capsule
disconnected and the feed
hose blanked
off.
8.
Battery:
Check the
electrolyte
level;
top-up
with
distilled
water
if
necessary.
9.
Belt
tension: Check the tension
of
all
driving
belts.
10. Brakes: Inspect foot brake and handbrake pad
linings;
fit
new pads
if
necessary.
When
renewing
footbrake pads, examine condition
of
dust excluders
on
calipers
and renew
if
necessary.
Manually
adjust
the handbrake ca 1 i per
mechanism.
Inspect
all
pipes
and connections,
rectify
if
necessary.
11.
Final
drive
unit:
Check the
oil
level;
top-up
if
necessary.
12.
Fluid
levels:
Check
all
fluid
levels.
13.
Front
suspension:
Tne
front suspension bal I
joints
are sealed
for
lite
and no maintenance
is
required
until
renewal
is
necessary or the
ball
joint
rubber
covers
are damaged. Inspect the rubber
covers
on
the
front
suspension bal I
joints;
if
the
covers are damaged,
fit
new
joints
and covers.
E10
- 2
14. Steering ball
joints:
Lubricate
the
six
grease
nipples.
Inspect the rubber covers
on
the bal I
joints;
if
the covers are found to be damaged the
joints
should
be
dismantled and new
parts
fitted
as
necessary.
15. Torque converter transmission: Renew
transmission
fluid.
When
checking
fluid
level,
avoid
contact
with
the exhaust gas
recirculation
valve,
heatshield
and associated pipes as these
components wi I I
be
hot.
Every 30 000 kilometres (18 000 miles)
or
18
months
whichever
is
the earlier
1.
Engine: Change the engine oi I and
fit
a new
oi I
filter
element.
2.
B3ttery: Check the
electrolyte
level;
top-up
with
distilled
water
if
necessary.
3.
Belt
tension: Check the tension of
all
driving
belts.
4. Brakes: Inspect footbrake and handbrake pad
linings;
fit
new pads
if
necessary.
When
renewing
footbrake pads examine condition
of
dust
excluders
on
calipers
and renew if necessary.
Manually
adjust
the
handbrake
caliper
mechanism.
Inspect
all
pipes
and connections.
Rectify
if
necessary.
5.
Fluid
levels:
Check al I
fluid
levels.
6. Torque converter transmission: Check
fluid
level and top·up if necessary.
When
checking
the
fluid
level,
avoid
contact
with
the exhaust gas
recirculation
valve.
heatshield
and
associated
pipes
as these components
will
be
hot.
Every 40 000 kilometres (24 000 miles)
or
2
years whichever is the earlier
1.
Air
injection
pump: Check tension
of
pump
pulley
driving
belt.
2.
Air
injection
system: Check the
air
injection
system for
leaks
and correct functioning. Renew
any
defective
items.
3.
Air
silencer:
Fit
a new paper
filter
element.
4. Automatic choke: Check the
flow
through the
choke stove pipe and check the system
for
correct
functioning.
5. Carburetters: Clean
air
valves.
Remove
inlet
unions from the
float
chamber covers and
fit
new
paper
filter
elements. Top-up
oil
level
in
air
valve
dampers. Check
tightness
of
float
chamber covers.
Check
float
chamber depression. Check and
if
necessary reset the
idle
speed. Check and if
necessary reset
the
choke
'fast-idle'
speed.
6. Carburetter
mixture
weakening
device:
Renew
air
filter
element
for
the carburetter mixture
weakening device.
7. Crankcase emission control system: Remove
and clean the gauze flame traps
in
the crankcase
breather tube. Clean the adapter
in
the choke
butterfly
housing.
8. Engine: Change the engine oi I and
fit
a new
oi I fi I ter element.
9. Engine
cooling
system:
Fit
a new engine
coolant thermostat and heater tap feed hose.
Examine the
condition
of
all
coolant
hoses.
Fit
new hoses
if
necessary.
u
To Next Page
Loading...
