-0
C:
(Q
0,
C:
w
C
c:-
m
:::,
C
ro
--,
t
~
0
U)
I-
Carburetter mixture weakening device
Fit
a new
air
filter
element.
Crankcase e.mission control system
Remove
and
clean the gauze flame traps in the
crankcase breather tube. Clean the adapter in the
choke
butterfly
housing.
Engine
Change the engine
oil.
Fit
a new
oil
filter.
Engine cooling system
Fit
a new thermostat.
Fit
a new heater tap feed
hose. Check the condition of
all
coolant
hoses and
fit
new hoses
if
necessary.
Exhaust gas recirculation system
Remove
and
clean the E.G.R.
valves
and
feed pipes.
Clean the
E.G.R.
orifices
in the carburetter •
tee'
piece. Check the E.G.R.
valves
for
correct
operation.
Exhaust manifolds
Check the torque tightness
of
the exhaust manifold
bolts.
Exhaust system
Fit
new
catalytic
converter assemblies. Inspect the
condition
of
the thermocouple and
wiring
in
each
catalytic
converter, renew
if
there
is
visual
evidence of damage.
Check
grass-fire
heatshields for damage.
Rectify
or renew shields to ensure that a minimum
clearance of 5
mm.
(0.20 in.)
is
maintained
between the heatsh
ields
and exhaust pipes.
Fuel evaporative emission control system
Fit
a new
air
Ii
I ter element to the evaporative
loss
control canister. Check the purge
flow
rate;
fit
a
new purge Ii ne f i I ter
if
necessary.
Ch
eek the
condition of the
pipes
and connections;
rectify
if
necessary.
Ignition system
Fit
new sparking plugs ensuring that the gaps are
correctly set.
Lubricate
the
distributor
spindle
(shaft bearings}
and automatic advance mechanism with engine oi I.
Check the
ignition
timing
and reset
if
necessary.
Battery
Check the level
of
the
electrolyte
and
if
necessary,
top~p
with
distilled
water.
Belt tension
Check the tension of
all
driving
belts
and reset
if
necessary.
Brakes
Inspect the foot brake and parking brake pad Ii nings;
fit
new
linings
if
necessary.
When
changing the
footbrake pads examine the condition of the dust
excluders
on
the
calipers;
renew if necessary.
Manually
adjust
the parking brake pads.
Inspect
all
brake
pipes
and connections; the
Distributor/Retailer
should report any
defects
to
the Owner.
Final
drive unit
Change the
oil.
Fluid
levels
Check
all
fluid
levels
and
correct
if
necessary.
Front suspension
Inspect the front suspension bal I
joint
rubber
covers;
if
the covers are found to
be
damaged
fit
new
joints
and covers.
Hydraul
1c
systems
Completely drain the
fluid
from the
hydraulic
circuits.
Thorough I y c I ean the brake
flu
id
reservoirs
and
sight
glasses
ensuring that
no
foreign matter
enters the systems.
Fi
11
the
hydraulic
systems
with
new approved
fluid.
Bleed the brakes and
height
control systems.
Propeller shaft
Lubricate
the grease
nipple
fitted
to the universal
joint
at
eilher
end
of
the propel I er shaft.
Rear wheel drive-shafts
Lubricate
the rear wheel
drive-shaft
outer
universal
coup Ii n
gs
with
approved grease.
Steering ball joints
Lubricate
the four grease n i
pp
I es.
Inspect the rubber covers on the
ball
joints,
if
the covers are found to be damaged, the
joints
should be dismantled and new parts
fitted
if
necessary.
Steering rack and pin
ion
assembly
Check the
clips
fitted
to the convoluted neoprene
seals
for
tightness.
Inspect the convoluted neoprene seals for
damage,
fit
new seals
if
necessary.
Torque converter transmission
Change the transmission
fluid
and
fit
a new
intake
strainer.
Preventive
Maintenance
Control I inkages
Apply
a few drops of engine oi I to the
accelerator
I ink age and to the gear range
selector
controls
adjacent to the transmission
casing.
E lectrica I system
Check
HII
interior
lamps,
exterior
lamps,
instruments, warning I
;i111ps
and
devices
for
correct
operation;
rectify
if
necessary.
Fuel
tilter
Clean the
filter
bowl.
Fit
a new
filter
element.
Fuel tank
Slacken the drain
plug
one
or
two turns and
allow
any accumulated water to drain away.
Height control mechanism
Disconnect the control
valve
linkage
ball
joints.
Clean, grease
and
refit
the
ball
joints.
E17 - 7
To Next Page
Loading...
