Room & Board MODA User Manual

Step 1: Assemble the lower section of the bunk bed first. Use the 2
Headboards as the end panels of the bottom bed.
ASSEMBLY INSTRUCTIONS
For MODA, POGO, DAYTON, PEPIN Bed and Bunk Bed
DO NOT USE POWER TOOLS!
Figure 1: Bunk Bed Assembly Steps 1-11
Figure 2: Bedrail Attachment Figure 3: Angled
Ladder Attachment
Begin here for Twin Bed Assembly. Step 2-4, Figure 2, Steps 9 &11.
Step 2: On the end panels, screw a Connector Bolt into each of the
threaded inserts completely. Back it off slightly in order to make the
through-hole in the bolt horizontal. (The Connector Bolts do NOT need to
be completely tightened.)
Step 3: Place one Steel Housing into each of the holes in the side of a
Bedrail. Align connector bolts with the holes on the end of the Bedrail,
slipping bolts through pre-drilled holes in the Bedrail and into the Housings.
Step 4: Place a Grub Screw inside each Housing, and use the Allen
wrench to tighten the Grub Screw. Repeat with the other Bedrail on the
same end panel, and then repeat Steps 3 & 4 for the opposite end panel. (For
twin bed alone, Adhesive Tabs are provided to cover the holes on top of the
Headboard.)
Step 5: Insert Steel Pins into the holes on top of the Headboards.
Step 6: Using the Footboards as end panels, assemble the upper bed by
attaching the Bedrails in the same manner as Steps 2-4 above.
Step 7: Lift the upper bed, and place on top of the Steel Pins. Push down
until the bottom of the Footboard is resting on top of the Headboard.
Step 8: Place the Long Guardrail on the wall side of the bed so that the
brackets are on the inside of the Bedrail, and attach each bracket with 2
Screws. Place the Short Guardrail on the front Bedrail against one of the
Footboards. (This allows an opening for the Ladder at the other end.) Screw
the Short Guardrail brackets to the inside of the Bedrail.
Step 9: Unroll and lay the Slatroll inside the Bedrails, with the webbing
facing up. With the 24 Wood Screws provided, use a Phillips-head
screwdriver to attach the slats. The first slat must be 2 inches from the end
of the Bedrail. Pull the Slatroll taught and secure the other end 2 inches from
the end of the Bedrail on that side; then secure all other slats. The slats
should be centered between the Bedrails, with a 1/8” gap between the end of
the slat and the Bedrail. This permits the Guardrail bracket to slip in
between the slat and the Bedrail.
Continue to step 10 on next page….

Room & Board MODA Specifications

General

Category	Indoor Furnishing
Brand	Room & Board
Material	Fabric or Leather
Frame Material	Hardwood
Style	Modern
Dimensions	Varies by model
Color Options	Multiple options available
Assembly Required	Yes

Summary

Bunk Bed Assembly Instructions

Step 1: Assemble Bottom Bed

Assemble the lower section of the bunk bed, using Headboards as end panels.

Step 2: Install Connector Bolts

Screw Connector Bolts into end panels, backing them off slightly for horizontal alignment.

Step 3-4: Attach Bedrails to End Panels

Place Steel Housings in Bedrails, align bolts, and tighten with Grub Screws.

Step 5: Insert Steel Pins

Insert Steel Pins into the designated holes on top of the Headboards.

Step 6-7: Assemble Upper Bed

Assemble the upper bed using Footboards as end panels and place it onto the lower bed.

Step 8: Attach Guardrails

Attach Long Guardrail on wall side and Short Guardrail on front Bedrail.

Step 9: Install Slatroll

Unroll Slatroll, attach slats with Wood Screws, ensuring proper spacing.

Step 10: Attach Ladder

Attach the ladder, either flat or angled, to the bottom bedrail.

Step 11: Place Mattress

Place mattress on Slatroll, ensuring correct size and height relative to guardrails.

Safety Warnings and Precautions

General Safety Guidelines

Follow warnings on bunk bed structure and carton; do not remove labels.

Mattress and Entrapment Safety

Use recommended mattress size and ensure surface is below guardrail edge.

Child Safety

Do not allow children under 6 on upper bunk; prohibit horseplay and jumping.

Operational Safety

Always use ladder for entry/exit; ensure all components are tight and undamaged.

Specific Hazards

Avoid water/flotation mattresses; prohibit more than one person on upper bunk.

Strangulation Hazard

Never attach items to the bunk bed that are not designed for its use.

Parts and Hardware Identification

Parts for Twin or Full Bed

Lists Headboard, Footboard, Bedrails, and Slatroll for Twin/Full beds.

Additional Parts for Bunk Bed

Includes Short Guardrail, Long Guardrail, Ladder, and Steel Pins.

Hardware for Assembly

Details Steel Housings, Connector Bolts, Grub Screws, Allen Wrench, and Wood Screws.