This option comes with a secondary Controller card,
Breakout Panel, Ethernet Interface card, and GPIO/Tally
card with rear module.
Caution: The upgrade of the Carbonite eXtreme with
a second switcher must be limited to service
personnel only and must be performed with the
frame/chassis in a de-energised state.
Important: The Carbonite eXtreme second switcher
upgrade is only compatible with Carbonite eXtreme
/ NK-3G144-X frame (2500AR-202-xx) running
software version 8.0 or higher. If you do not have this
frame or software, or are unsure about the model of
your frame, please contact Ross Video Technical
Support for more information.
SideShot Custom Control Shot Box
(CPS-SideShot)
This option provides quick access to the rst 24 custom
controls on the rst 4 custom control banks of the
switcher.
Remote Panels
This option provides external control for selecting sources
on an Aux bus from a remote panel. There are a number
of options for the remote control panels, depending on
your requirements.
On Carbonite eXtreme these panels can be congured
to operate as an X-Y, cut-bus or multi-cut bus panel for
the router subsystem, or as a control panel to select
sources any bus or run custom controls for the switcher
sub-system. Every control panel in the system can be
independently congured to meet the needs of the
particular operator. Connects to the switcher through an
NK-IPS over ethernet (T-BUS connection between the
NK-IPS and remote control panel).
On Carbonite and Carbonite Black these panels connect
to the switcher through an NK-IPS over ethernet (T-BUS
connection between the NK-IPS and remote control
panel).
DescriptionOption
Adds the 32 source button NK remote
control panel.
NK
Adds the 40 source button RCP-NKM
remote control panel with integrated
backlit display.
RCP-NKM
Adds the 17 mnemonic button
RCP-NKQ remote control panel.
RCP-NKQ
DashBoard Display
(CBPS-DashMenu)
The DashBoard Display combines a DashBoard computer
with a touchscreen into a single unit that can be installed
onto a standard VESA-100 mount. The DashBoard
Display connects to the switcher over ethernet to provide
the advanced menu system interface to the setup and
operation of your Carbonite or Carbonite Black switcher.
The DashBoard Display eliminates the need to connect
another computer to your switcher network just to run
DashBoard.
SMC-9901 Serial to MIDI Converter
(SMC-9901)
The SMC-9901 Serial to MIDI Converter is used to allow
control of an Audio Mixer from a Ross Video switcher.
The SMC-9901 provides a single DB-9 connector for
38,400 baud serial RS-422 communication, one 5-pin
DIN connector for MIDI in, and two 5-pin DIN
connectors for MIDI out. Power, Serial Tx and Rx, MIDI
In and MIDI Out Status LEDs next to the ports show
activity status.
The SMC-9901 connect to the switcher via the serial port
on the frame, or an external port expander such as the
Comtrol
®
DeviceMaster
®
.
SHC-9642 SDI to HDMI Converter
(SHC-9642)
The SHC-9642 SDI to HDMI Converter is a high-quality
signal conversion solution within the family of GearLite
compact, self-contained modular products. The
SHC-9642 is the ideal solution for converting any SDI
input signal (up to 3Gb/s) into an HDMI Type-A output
format. User-selectable audio decoding is available with
unbalanced, stereo analog audio outputs. Up to 16
channels of embedded audio are selectable, in stereo
pairs, for de-embedding and decoding.
Onsite Operational Training
(CARBONITE-OTR-1DAY)
Although Ross Video switchers are designed to be as
easy as possible to install and operate, training is highly
recommended to ensure that the process of taking your
Ross Video switcher to air is a smooth one.
Training is provided on the customer's equipment at their
site. Expenses are extra, and billed at the completion of
the visit. Ross Video cannot guarantee the availability
of a local Trainer, as such, travel costs to all locations
will be invoiced at cost. Two (2) days, or more, of
Carbonite Configuration Guide (v11.1) — System Options • 11
To Next Page
Loading...
