Rossi DZ ATTO TURBO - User Manual

Tx
Smart Products
Sliding Line
DZ ATTO TURBO / DZ NANO TURBO/ DZ NANO Bi TURBO/
DZ3 / DZ3 TURBO / DZ4 / DZ4 TURBO / DZ4 Bi TURBO
SIA 30 FS
Installation
1 - Observe if the gate is sliding freely in all its route, observing
support guide, rail, stops and pulleys
2 - Provide a power and ground point, passing a conduit,
starting from the driver to the power board with a 10A bipolar
circuit breaker.
NOTE: It is mandatory to install a shutdown device (bipolar
circuit breaker
with minimum contact opening equal to 3mm)
that must be incorporated into fixed wiring.
3 - Provide the means by which you want to fix the drive.
• Concrete Base • Metal Base • Cross Arm Brace (Air Base) Use
the measurements in the manual to mark the location of the
bolts.
4- Place the washers on the base, screw the driver onto the
washers and place the driver in the manual mode.
5 - Close the gate, support the rack on the gear and fix the bar
in the gate with solder or screw, 30 by 30 cm.
6 - Once the racks have been fixed, remove the washers placed
on the base and fix the motor again, and check the spaces
between the rack and the gear.
NOTE: " The washers placed at the beginning of the racks
attachment serve to give the minimum mandatory height of 2
mm between the rack and the external gear of the engine."
NOTE: " Failure to observe this distance may result in wear on the
drive's internal and external gears or breakage of the rack with
engine starting."
7- Adjust the end magnets in open mode FA and closed FF,
placing a magnet on each end of the rack, observing the polarity of
each magnet between open and closed gate.
NOTE: "The magnets must always be attached to the angle
bracket, even during opening and closing adjustments to
prevent damage to the control unit"
8 - Fix the control unit on the support guide inside the actuator
(fixing instructions Page2).
9 - End of stroke HALL sensor The hall sensor identifies the
polarity of the magnets, north and south. (instructions Page 6)
NOTE: For bench tests, it should simulate the movement of
the magnet installed in the gate, remembering that when the
control is activated the limit switch must be active.
In the installation and adjustment of the magnets, in the first
two commands the control unit must recognize the FA and FF
magnets.
10 - The use of the Active infrared sensor - SIA 30 is
MANDATORY to activate the system of anti-locking protection,
avoiding collision with obstacles, accidents with people or material
goods.
11 - The gates and actuators need periodic maintenance and
lubrication every 6 months for proper operation.
Rev 05/18 - COD. 12443
www.rossiportoes.com.br
Page 1
1
Support guide
Rail and Stopper
Pulleys
FA -End of stroke open gate
FF - End of stroke closed gate
2
3
4
Washers

Summary

Installation Guide

Initial Checks and Drive Mounting

Checks gate movement, power, fixing drive to base, rack attachment, and initial adjustments.

Limit Switch and Safety Sensor Setup

Guides adjustment of end magnets, HALL sensor, and mandatory SIA 30 FS sensor for safety.

Periodic Maintenance Schedule

Recommends periodic maintenance and lubrication every 6 months for optimal operation.

Technical Measurements and Fixing

Drive Model Dimensional Specifications

Provides dimensional data for various DZ and NANO gate drive models.

Drive Mounting Methods

Illustrates central fixing and screw fixing methods for the drive unit.

Hall Magnet Polarity Identification

Shows identification of FA (Open) and FF (Closed) Hall magnets for limit switch setup.

Technical Specifications and Safety

Drive Model Technical Data

Lists technical data like tension, power, frequency, and speed for various DZ and BiTurbo models.

Important Safety Instructions

Critical safety guidelines for installation and operation, including mandatory sensors and electrical safety.

SIA30 FS Active Infrared Sensor

Sensor Installation and Features

Covers mounting, distance, height, alignment, and features of the SIA30 FS sensor.

Manual Gate Opening Procedure

Step-by-step process for manually unlocking and opening the gate in emergencies.

Digital Access Key Configuration

Explains how to add and erase digital access key codes for system access.

Control Unit Wiring and Functions

Warranty Terms and Conditions

Details warranty coverage, limitations, and conditions for product defects and misuse.

Control Unit Wiring Diagram

Illustrates connections for motor wires, power input, and external accessories like photocells.

Control Unit Features Overview

Lists key features of the control unit such as automatic source, memory, and programming options.

Control Board Operations

Motor and Accessory Connections

Details connections for motor wires, power input, and external devices like traffic lights.

Dip Programming and Settings

Explains dip switch settings for soft stop, lock, pause, and building/residential modes.

Electronic Brake Adjustment

Guides the adjustment of the electronic brake levels for controlling gate deceleration.

Rossi DZ ATTO TURBO Specifications