You need to replace the batteries when:
1. low battery icon appears on display.
2. the START/STOP key is pressed and nothing appears on display.
Caution: 1. Batteries are hazardous waste. Do not dispose them together with the household
garbage.
2. There are no user serviceable parts inside. Batteries or damage from old batteries are
not covered by warranty.
3. Use exclusively brand batteries. Always replace with new batteries together. Use
batteries of the same brand and same type.
Applying the Cu
1. Unwrap the arm cu, leaving the end of the cu through the D-ring of the cu.
2. Put your left arm through the cu loop. The color strip indication should be positioned closer
to you with the tube pointing in the direction of your arm (Fig.1). Turn your left palm upward
and place the edge of the arm cu at approximately 1.5 to 2.5 cm above the inner side of the
elbow joint. Tighten the cu by pulling the end of the cu.
3. Center the tube over the middle of the arm. Press the hook and loop material together securely.
Allow room for 2 ngers to t between the cu and your arm. Position the artery mark (Ø) over
the main artery (on the inside of your arm) (Fig. 3,4).
Note: Locate the main artery by pressing with 2 ngers approximately 2 cm above the bend of
your elbow on the inside of your left arm. Identify where the pulse can be felt the strongest.
This is your main artery.
4. Plug in the cu connecting tube into the unit (Fig. 5).
5. Lay your arm on a table (palm upward) so the cu is at the same height as your heart. Make sure
the tube is not kinked (Fig. 6).
Measurement Procedures
Important Notes:
Here are a few helpful tips to help you obtain more accurate readings:
• Blood pressure changes with every heartbeat and is in constant uctuation throughout the day.
• Blood pressure recording can be aected by the position of the user, his or her physiological condition
and other factors. For greatest accuracy, wait one hour after exercising, bathing, eating, drinking bever-
ages with alcohol or caeine, or smoking to measure blood pressure.
• Before measurement, it’s suggested that you sit quietly for 15 minutes as measurement taken during a
relaxed state will have greater accuracy. You should not be physically tired or exhausted while taking a
measurement.
• Do not take measurements if you are under stress or tension.
• During measurement, do not talk or move your arm or hand muscles.
• Take your bl ood pressure at normal body tempera ture. If you are feeling cold or hot, wait a while be -
fore taking a measurement.
• If the monitor is stored at very low temperature (near freezing), have it placed at a warm location for at
least one hour before using it.
• Wait about 5 minutes before taking the next measurement.
1. Press the ON/OFF key. All display will appear for approximately two seconds before returning to “0”.
One long beep and three short beeps will be heard. The unit is ready for measurement at this point.
2. Press the bulb to increase pressure in the arm cu. The display will show the pressure reading within
the cuff. Continue pumping until the pressure reaches approximately 50~60 mmHg above your
normal systolic pressure. Three short beeps will be heard as you pump the pressure to 170 mmHg to
remind you to stop pumping.
If your blood pressure is higher than 180 mmHg and the pressure in cu is not enough, an upward
arrow (
) will display and continuous short beeps will be heard to remind you that you should con-
tinue pumping the pressure more than to 200 mmHg. You will hear three short beeps to remind you
to stop pumping.
3. Sit still and wait for the monitor to deate and measure your blood pressure. It is important to remain
still and quiet during measurement. Any signicant movement may aect measurement results.
4. Upon completion of the measurement cycle, the monitor will display systolic pressure, diastolic pres-
sure and pulse rate readings at once at the sound of a long beep. Measurement is now completed, and
the reading is automatically stored in the monitor.
5. Press the ON/OFF key to rapidly deate and turn o the power. If no key is pressed, the unit will shut o
automatically in 1 minute.
Note: 1. This monitor automatically switches o approximately 1 minute after last key operation.
2. To i nterr up t the measure men t, simply pre ss the Memor y or O N/ OFF key ; the cu will d eate
immediately.
3. During the measurement, do not talk or move your arm or hand muscles.
Fig.1
Fig.2
Fig.3
Fig.4
Fig.6
Fig.5
Fig.7
6. This cu is suitable for your use if the arrow falls within the solid color line as shown on the
right (Fig. 7). If the arrow falls outside the solid color line, you will need a cu with other cir-
cumferences. Contact your local dealer for additional size cus.
To Next Page
Loading...
