ROYAL HG120 PAPER SHREDDER
Cautions:
1. Never allow children to shred or play with paper shredder or else serious injury
could occur.
2. Do not place hands or fingers into the shredder throat as serious injury could
result.
3. Never spray canned air or any type of spray lubricant into the shredder while
shredder is plugged in or serious injury could result.
4. Never place any lubricants or cleaning solutions into the paper shredder or else
serious injury could result.
5. Keep all loose articles of clothing, ties, jewelry, hair or other small items away from
the feed opening to prevent injury.
6. Remove all paper clips and staples from paper before shredding. The shredder
will cut staples and small paper clips; however, proper discretion is recommended.
7. Keep the shredder turned off or unplugged when not in use for prolonged periods
of time..
8. When manually changing feed direction, pause long enough for the motor tostop to
avoid possible damage to the motor.
9. Always turn off and unplug the shredder prior to moving, cleaning or emptying the
wastebasket.
10.Empty the wastebasket frequently to avoid possible paper jams caused by
shredded material being pulled back into the cutter assembly.
Setup:
1. The HG120 shredder should be placed on a flat level surface. Depending on the
type of floor surface where the shredder is to be placed, casters have been
included andcan be installed easily. It is recommended that casters only be used
if the shredder is being placed on a hard smooth surface.
2. Make sure that the wastebasket is completely inserted in the shredder and that it
fits flush with the shredder cabinet.
3. Plug the power cord into any standard 115-volt AC outletwhich shall be installed
near the equipment and shall be easily accessible.
4. Place the switch in the Auto positon. The Power LED should light up. You are
now ready to start shredding.
Operating the shredder:
With the electrical cord plugged in, the switch in the Auto position, shredder wastebasket
properly in place, the Power LED will light up. This means that the shredder is now ready
for operation. When the paper is inserted into the feed opening, the shredding process
will start automatically and stop when the paper has completed its travel through the feed
opening.
The HG120 mode selection switch is located on the top of the shredder. Also located on
top of the shredder is the Power LED. Their purposes are:
1. When the switch is placed in the AUTO position, the shredding process will
start when paper is inserted into the feed opening and will continue until it has
completely passes through the feed opening.
2. The Rev position is used to assist in the removal of a paper jam,which reverses the
shredding process prior to a completed forward cycle, thus clearing the cutters.
When switching from Auto to Rev, always stop in the off position to prevent possible
damage to the motor.
3. It is recommended to turn the shredder off when the shredder is not being used for
a prolonged period of time.
2
ROYAL HG120 PAPER SHREDDER
4. When the Power LED is lit up it lets the user know that the wastebasket is inserted
correctly and that the shredder is turned on and ready for use. If the Power LED
does not light up, make sure that the plug is plugged in and the basket is inserted
correctly.
Shredder capacity:
The HG120 will shred up to twelve (12) sheets of 20-lb. bond paper and will accept paper
widths up to 8 2/3". When shredding small material like envelopes or credit card receipts,
insert them in the middle of the feed opening.
Paper jams and motor overload situations:
The HG120 is equipped with an automatic motor overload protection circuit. The HG120
will automatically terminate power case of the following abnormal situations:
1. Operating the shredder at the maximum twelve (12) sheets capacity continuously
for a prolonged period of time.
2. Exceeding the shredding capacity, eg. Inserting more than twelve (12) sheets of
20-lbs. paper in one pass, or if the paper is not fed squarely into the feed opening.
Both abnormal operations may result in the activation of the automatic thermal motor
overload protection circuit, which terminates the power to the shredder. A paper jam could
cause the thermal motor overload protection to terminate AC power to the motor. Never
allow the shredder to remain in a jammed condition with the AC power turned on. If this
occurs you should:
In case of a minor paper jam:
1. Place the switch in Rev and pull the remaining sheets of paper out of the feed
opening. Remove the unshredded portion of paper from the top and clear any excess
paper shreds from the feed opening. When the excess paper has been removed
place the switch back into the Auto position.
In case of a major paper jam:
1. Turn off or unplug the power cord from the AC outlet and wait at least 30 minutes for
the thermal overload protection to reset.
2. Plug in the AC power cord and place the switch back into the Auto position. If paper
was left inside the feed opening prior to the overload, place the switch in Rev and
grasp the excess paper from the top and pull it out. Be careful not to place your
fingers near the feed opening or serious harm could result. Clear any excess paper
shreds from the feed opening.
3. Place the switch back into the Auto position. You are now ready to resume normal
shredding.
Specifications:
Shred Type: Cross-Cut
Shred Width: 5/32"x 1 1/3” (4mm x 33mm)
Shredding Capacity: 12 Sheets
Feed Opening: 8 2/3" (220mm)
Weight: 13.5 Ibs.(6 kgs)
Input: 115 volt AC, 6 amp.
3
To Previous Page
Loading...
Need help?
General
