To Next PageTo Next Page
Need help?Do you have a question about the Rubbermaid 5L10 and is the answer not in the manual?
Check local building codes, ordinances, restrictions, and neighborhood governances before assembly.
Ensure proper assembly and performance by building on a solid, level surface like concrete or a treated-wood platform.
Choose an area with easy access and proper drainage for water to run away from the shed location.
Review all assembly steps in order and check the parts list to ensure no parts are missing.
Cut wall slot tabs using a utility knife and knock them out with a rubber mallet and screwdriver.
Knock out tabs for door hinges using a rubber mallet and screwdriver on the front floor panel.
Drill pilot holes through the top surface of the floor for specific locations on the front floor.
Prepare screw holes, drill pilot hole, and snap Front Left Side panel (G) into Front Floor (A).
Prepare screw holes, connect Left Back panel (D) to Front Left Side (G), and engage floor snaps.
Prepare screw holes, drill pilot hole, and snap Front Right Side panel (H) into Front Floor (A).
Prepare screw holes, connect Right Back panel (F) to Front Right Side (H), and engage floor snaps.
Install 5 Wall Connectors (WC) to connect the Left Back and Right Back Panels (D and F).
Install the Front Roof panel (J) onto side sections, aligning tongues on top of side walls into roof grooves.
Position Roof Brace (RB) onto side walls, lower roof, align brace into Front Roof pocket and secure with screws.
Install Left Door (L) and Right Door (K) into hinge openings of the Front Floor (A) and Front Roof (J).
Install four screws (AA) into the roof, two on each side wall, passing through the Roof Brace (RB).
Install screws (AA) into 6 locations at the bottom of wall panels to secure walls to the floor.
Install the Lock Hasp (X) into the opening on the Right Door (K).
Install the Door Handle (T) onto the Left Door (L) using four screws (AA).
Periodically check the shed to ensure it remains stable and the site remains level.
In high wind areas, anchor the shed to a platform or ground using proper fasteners.
Wash the shed with a garden hose or mild detergent; avoid abrasive cleaners.
Do not store hot items, lean heavy items against walls, keep doors closed, and do not climb on the roof.
Check local building codes, ordinances, restrictions, and neighborhood governances before assembly.
Ensure proper assembly and performance by building on a solid, level surface like concrete or a treated-wood platform.
Choose an area with easy access and proper drainage for water to run away from the shed location.
Review all assembly steps in order and check the parts list to ensure no parts are missing.
Cut wall slot tabs using a utility knife and knock them out with a rubber mallet and screwdriver.
Knock out tabs for door hinges using a rubber mallet and screwdriver on the front floor panel.
Drill pilot holes through the top surface of the floor for specific locations on the front floor.
Prepare screw holes, drill pilot hole, and snap Front Left Side panel (G) into Front Floor (A).
Prepare screw holes, connect Left Back panel (D) to Front Left Side (G), and engage floor snaps.
Prepare screw holes, drill pilot hole, and snap Front Right Side panel (H) into Front Floor (A).
Prepare screw holes, connect Right Back panel (F) to Front Right Side (H), and engage floor snaps.
Install 5 Wall Connectors (WC) to connect the Left Back and Right Back Panels (D and F).
Install the Front Roof panel (J) onto side sections, aligning tongues on top of side walls into roof grooves.
Position Roof Brace (RB) onto side walls, lower roof, align brace into Front Roof pocket and secure with screws.
Install Left Door (L) and Right Door (K) into hinge openings of the Front Floor (A) and Front Roof (J).
Install four screws (AA) into the roof, two on each side wall, passing through the Roof Brace (RB).
Install screws (AA) into 6 locations at the bottom of wall panels to secure walls to the floor.
Install the Lock Hasp (X) into the opening on the Right Door (K).
Install the Door Handle (T) onto the Left Door (L) using four screws (AA).
Periodically check the shed to ensure it remains stable and the site remains level.
In high wind areas, anchor the shed to a platform or ground using proper fasteners.
Wash the shed with a garden hose or mild detergent; avoid abrasive cleaners.
Do not store hot items, lean heavy items against walls, keep doors closed, and do not climb on the roof.
General| Material | Plastic |
|---|---|
| Color | Clear |
| Lid Type | Snap-on |
| Stackable | Yes |
| Dishwasher Safe | Yes |
| Freezer Safe | Yes |
| Microwave Safe | Yes |
