To Next PageTo Next Page
Need help?Do you have a question about the Ryobi GD200 and is the answer not in the manual?
General| Security | Rolling code technology |
|---|---|
| Max Door Height | 7 feet |
| Safety Features | Auto-reverse, photoelectric sensors |
| Voltage | 120V |
| Speed | 7 inches per second |
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS GARAGE DOOR OPENER to reduce the risk of electric shock, fire and/or serious personal injury.
Rules for safe handling and disposal of batteries to prevent sparks, burns, or fire.
Instructions for safe charging of batteries, including warnings about incompatible battery types and proper handling.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
Explains symbols related to safety alerts, eye protection, electrocution, moving doors, and recycling.
This product may contain chemicals, including lead, known to the State of California to cause cancer, birth defects or other reproductive harm.
This product has a precision-built electric motor. It should be connected to a power supply that is 120 volts, AC only, 60 Hz.
Module Capacity, Max Garage Door Height, Bulb Type, Drive Type, Input, Motor, No Load Speed, Rail Length.
The following items are included with your garage door opener: Header Bracket, Wing Nut, Mounting Strap, Door Bracket...
The following tools (not included or drawn to scale) are needed for assembly and adjustments: Drill Bit, Screwdriver, Level...
Carefully remove the product and any accessories from the box. Make sure that all items listed in the loose parts list are included.
Insert the edge of the end rail into the sleeve. Slide together until rail clicks in place.
Place the power head on a towel or the packaging material with the light cover facing down.
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
CHECK THE CONDITION OF THE DOOR AND IDENTIFY THE SPRING TYPE. If the garage door does not move smoothly, binds, or is out of balance...
To avoid serious personal injury, attach header bracket to sound structural support on header wall.
Angle the rail assembly so that it rests against the header bracket. Align the holes in the bracket with the holes in the rail assembly...
Mount garage door opener to sound structural support on ceiling. NEVER mount the garage door to drywall or false ceiling grids.
Do not engage the emergency release while the garage door is open, do not use the emergency release rope to raise or lower the garage door...
Before installing the door bracket, ensure that your door has proper horizontal and vertical support.
Secure straight door arm to the rear of the outer trolley using medium clevis pin and hitch pin.
Assemble the safety sensors by inserting the sensor stud through the long slot in the bracket and securing with a wing nut.
Find desired location indoors and in sight of the garage door. NOTE: The keypad should be at least five feet above the floor...
Find desired location outdoors and in sight of the garage door.
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: READ AND FOLLOW ALL INSTRUCTIONS.
CONNECTING THE GARAGE DOOR OPENER TO A POWER SUPPLY. For AC power: Assemble and mount...
The garage door opener can power a variety of AC and DC modules.
DO NOT operate the garage door opener unless the safety sensors are installed and working correctly.
Provides a table of LED functions, problems, and solutions for safety sensors.
The console on your garage door opener makes it easy to set the open and close positions of your door.
Press and hold the UP button for three seconds. After you release the button, it will begin blinking...
Press and hold the DOWN button for three seconds. After you release the button, it will begin blinking...
Press and release the UP button and ensure that the door moves to the programmed open position.
To raise or lower the garage door, press and release the UP/DOWN button.
Test the automatic reversal system every month and after any adjustments are made to the garage door travel limits.
Once you begin programming the outdoor keypad, you have two minutes to complete each step.
Press the PROGRAM button on the garage door opener's console. The main garage door opener's LEDs will turn off...
A router with Wi-Fi is needed in order to use the smartphone app.
Before inspecting, cleaning or servicing the machine, lower the garage door, shut off motor, wait for all moving parts to stop...
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents...
Remove the battery cover by inserting the edge of a coin into the slot and twisting.
Check the power head, rail, brackets, door arms, track, and rollers for loose or damaged parts.
The following accessories are not included with your garage door opener but may be available where you purchased this product.
All of the console buttons are blinking continuously. POSSIBLE CAUSE: DC voltage below 24V.
Garage door opener is in the fully open position and cannot be closed with a car remote, smart phone, or keypad.
One World Technologies, Inc., warrants to the original retail purchaser that this RYOBI™™ brand garage door opener is free from defect...
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions...
