Ryobi RLL18-0 User Manual

FRONT PAGE
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
RLL18

Ryobi RLL18-0 Specifications

General

Type	LED Work Light
Power Source	Battery
Voltage	18V
Weight (without battery)	1.2 kg
Features	rotating head

Summary

INTENDED USE

The lantern is intended for general illumination. Do not use the product in wet conditions.

Specifies the intended use of the lantern for general illumination and advises against wet conditions.

LANTERN SAFETY WARNINGS

The light source of this luminaire is not replaceable. When the light source reaches its end of life the whole luminaire shall be replaced.

Informs that the light source is not replaceable and the entire unit must be replaced.

Use only with recommended battery pack and charger. Any attempt to use another battery pack will cause damage to the product and could possibly explode, cause a fire, or personal injury.

Warns to use only recommended battery packs and chargers to avoid damage or injury.

Do not disassemble the product.

Advises against disassembling the product.

If wrapped or in contact with fabrics, the lens can produce sufficient heat to melt some fabrics. To avoid serious personal injury, never allow the lens to come in contact with anything.

Warns about the heat generated by the lens and potential contact hazards.

Do not place the product or battery pack near fire or heat. This will reduce the risk of explosion and possible injury.

Advises against placing the product near heat sources to prevent explosion risk.

Remove the battery pack before starting any work on the product.

Instructs to remove the battery pack before performing any product work.

Do not store the product in a damp or wet location, or in a location where the temperature may reach or exceed 40°C. For example, inside sheds, vehicles, or metal buildings in the summer.

Provides storage guidelines regarding moisture and temperature limits.

BATTERY SAFETY WARNINGS

To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack, or charger in fluid or allow fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.

Warns against immersing battery packs and chargers in fluids to prevent short circuits.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national provisions and regulations.

Instructs to transport batteries according to relevant regulations.

Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

Provides guidelines for safe battery transport, including packaging and protection.

KNOW YOUR PRODUCT

See page 64.

Directs the user to page 64 for product identification.

1. Hanging bracket

Identifies the hanging bracket component of the product.

2. Power button

Identifies the power button component of the product.

3. USB charging port

Identifies the USB charging port component.

4. Battery port

Identifies the battery port component of the product.

5. Operator's manual

Identifies the operator's manual documentation.

6. Battery pack

Identifies the battery pack component.

7. Charger

Identifies the charger component.

MAINTENANCE

Use only original accessories and spare parts. Should components need to be replaced which have not been described, please contact

Advises using only original accessories and spare parts, and contacting for replacements.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.

Encourages recycling of raw materials and proper sorting of the product and packaging.

SYMBOLS IN THIS MANUAL

Note

Indicates a note or important information.

Parts or accessories sold separately

Indicates items available for separate purchase.

SYMBOLS

Safety Alert

Symbol indicating a safety alert or warning.

Volts

Symbol for electrical voltage measurement.

Direct current

Symbol for direct current electrical flow.

European Conformity Mark

Symbol indicating compliance with European standards.

British Conformity Mark

Symbol indicating compliance with British standards.

RYOBI® WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

States that the product is covered by warranty in addition to statutory rights.

1. The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.

Details the 24-month warranty period for consumers and its conditions.

2. There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.

Explains the process for extending the warranty period through online registration.

3. The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:

Details what the warranty covers, limitations, and conditions for invalidity.

4. For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender's address and accompanied by a short description of the fault.

Provides instructions for product servicing and shipping to authorized service stations.

5. A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected

Clarifies that repairs/replacements are free but do not extend the warranty period.

6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey, Russia, and the United Kingdom. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.

Specifies the geographical validity of the warranty and how to proceed outside these areas.

AUTHORISED SERVICE CENTRE

Any request or issue with the product can be addressed to your local authorised service centres (visit www.ryobitools.eu) or directly to: Techtronic Industries GmbH, Max Eyth Straße 10, 71364 Winnenden, Germany. Please state the serial number and product type printed on the label.

Provides contact information for authorized service centers for inquiries and issues.