What to do if my Saf-Fro Digisteel 420 Welding System displays the message EEEE00002222 iiiinnnnuuuu?
If your Saf-Fro Welding System displays the message EEEE00002222 iiiinnnnuuuu, ensure that the mains voltage is between 360V and 440V. If the voltage is outside of this range, have your electrical system checked by a qualified technician.
How to fix the error message E01E01 OndE01E01 OndOndOnd on my Saf-Fro Welding System?
To address the error message E01E01 OndE01E01 OndOndOnd on your Saf-Fro Welding System, you should: 1. Check the mains supply to each phase. 2. Check the fuses on the auxiliary power supply card F1 (6A) 30V AC and F5 (3A) 400V AC. 3. Check the position of switch I1 on the Cycle Card in front of Item 1. 4. Check the connectors of the B1 Cycle card and the B30, 31, 32, 33 Supply Card.
General| Brand | Saf-Fro |
|---|---|
| Model | Digisteel 420 |
| Category | Welding System |
| Language | English |
Details the HPS welding process, its advantages, and ALW's role.
Provides detailed technical specifications for DIGISTEEL 420 and 520 power sources.
Provides detailed technical specifications for DIGISTEEL 420 and 520 power sources.
Lists the technical specifications for the COOLER II PW cooling unit.
Guides on connecting the DIGISTEEL to the electrical mains and compatible generators.
Steps for connecting the gas hose and cylinder, including gas flow rate recommendations.
Guides on connecting the DIGISTEEL to the electrical mains and compatible generators.
Instructions for connecting the wire feeder unit to the power source.
Instructions for initial startup, including generator calibration.
Details how to connect the welding torch and cooling unit, including torch selection.
Details how to connect the welding torch and cooling unit, including torch selection.
Explains the functions of each control and indicator on the front panel of the DIGISTEEL.
Details how to interpret display readings and use functions like JOB indicator and measurement indicator.
Describes the DIGISTEEL's coated electrode welding mode and parameter configuration.
Explains how to access and navigate the SETUP menu for configuration and parameter settings.
Explains the 2-stroke welding cycle and its operation.
Explains how to choose the welding cycle (2T, 4T, Spot) and mode (synergic/manual).
Details the functions of the RC JOB remote control for setting parameters, calling programs, and modifying them.
Lists internal and external components with their part numbers for replacement.
Addresses issues like trigger faults, no welding power, and troubleshooting steps like factory reset.
Guides on connecting the DIGISTEEL to the electrical mains and compatible generators.
Steps for connecting the gas hose and cylinder, including gas flow rate recommendations.
Instructions for connecting the wire feeder unit to the power source.
Instructions for initial startup, including generator calibration.
Details how to connect the welding torch and cooling unit, including torch selection.
Explains the functions of each control and indicator on the front panel of the DIGISTEEL.
Details how to interpret display readings and use functions like JOB indicator and measurement indicator.
Explains how to access and navigate the SETUP menu for configuration and parameter settings.
Explains the 2-stroke welding cycle and its operation.
Details the functions of the RC JOB remote control for setting parameters, calling programs, and modifying them.
Lists internal and external components with their part numbers for replacement.
Troubleshoots common issues related to power supply, display messages, and generator operation.
Troubleshoots common issues related to power supply, display messages, and generator operation.
Addresses issues like trigger faults, no welding power, and troubleshooting steps like factory reset.
Guides on connecting the DIGISTEEL to the electrical mains and compatible generators.
Steps for connecting the gas hose and cylinder, including gas flow rate recommendations.
Instructions for connecting the wire feeder unit to the power source.
Instructions for initial startup, including generator calibration.
Details how to connect the welding torch and cooling unit, including torch selection.
Explains the functions of each control and indicator on the front panel of the DIGISTEEL.
Details how to interpret display readings and use functions like JOB indicator and measurement indicator.
Explains the 2-stroke welding cycle and its operation.
Details the functions of the RC JOB remote control for setting parameters, calling programs, and modifying them.
Lists internal and external components with their part numbers for replacement.
Addresses issues like trigger faults, no welding power, and troubleshooting steps like factory reset.
Provides detailed technical specifications for DIGISTEEL 420 and 520 power sources.
To Next Page