EasyManua.ls Logo

safety-kleen 90 - User Manual

safety-kleen 90
14 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Part No. SK 816008
Date: February 23, 2011
MODELS 90, 91, and 94
MANUAL AQUEOUS
PARTS WASHERS
Support Manual
All rights reserved. The information in this document is proprietary and confidential. No part of this
publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means -
electronic, mechanical, photocopying, recording, or otherwise - without prior written permission of Safety-
Kleen Systems, Inc. and distribution hereof is strictly limited to authorized Safety-Kleen personnel and to
those purchasing the equipment.
Safety-Kleen Systems, Inc. 5360 Legacy Drive, Building 2, Suite 100 Plano, TX 75024

Table of Contents

Questions and Answers

  • N
    Nicole HoltSep 10, 2025
    What to do if the half moon is damaged on my safety-kleen Washer?
    • A
      Andrew PowellSep 12, 2025
      If the tabs are broken or the half moon is lost on your safety-kleen Washer, replace it with SK #232037.
  • L
    Lonnie OliverAug 22, 2025
    What to do if the pump doesn’t work on my safety-kleen 90 Washer?
    • T
      Tara GrahamAug 23, 2025
      If the pump on your safety-kleen Washer isn't working, check the PUMP circuit breaker's ON/OFF position. Also, verify the power cord connection. Finally, make sure the electrical outlet is functioning correctly by plugging in another appliance or using an outlet tester.
  • J
    jodikiddAug 25, 2025
    How to resolve a drainage issue in my safety-kleen 90 Washer?
    • P
      pparkerAug 25, 2025
      To address a drainage issue in your safety-kleen Washer, start by removing any debris from the crumb cup and/or strainer basket and dispose of it according to local regulations. You should also replace the filter sock.
  • C
    Carolyn OrtegaAug 27, 2025
    What to do if there is fusible link damage in my safety-kleen Washer?
    • N
      nhowardAug 27, 2025
      To address fusible link damage on your safety-kleen Washer: Ensure the lid moves freely without obstruction and that the standpipe for the Model 90 (SK #2244) or the Model 94 (SK #2144) is in place and the locknut is tight. If the standpipe is loose, tighten the locknuts SK #5515 using an adjustable wrench. Remove any broken pieces of the old fusible link and replace it with a new one.
  • V
    veronica56Aug 27, 2025
    Why is my safety-kleen Washer leaking?
    • Y
      yroblesAug 27, 2025
      If your safety-kleen Washer is leaking, first check for any loose hoses that might be leaking on the floor and re-route them if necessary. If the drum or vat is leaking, replace them as soon as possible.
  • S
    Samuel BrandtAug 29, 2025
    How to fix a lamp that doesn’t turn on in my safety-kleen 90 Washer?
    • P
      Patrick TateAug 29, 2025
      If the lamp on your safety-kleen Washer doesn't turn on, check the LAMP circuit breaker's ON/OFF position. Try turning the unit on and off again, ensuring the momentary switch always points down. Flip the On/Off switch on the lamp and push the Start/Stop button on the control box. Verify the power cord connection and ensure the electrical outlet is functioning. If needed, replace the bulb, using no more than a normal 40-watt bulb.
  • J
    John AndersonSep 18, 2025
    How to check customer outlet for power for safety-kleen 90?
    • P
      powelljohnSep 18, 2025
      Use an Outlet Tester to confirm proper wiring for your safety-kleen Washer.
  • A
    Amy BushSep 12, 2025
    How to stop lamp flashing (nuisance tripping) on my safety-kleen 90 Washer?
    • E
      Emily WoodsSep 12, 2025
      If the lamp is flashing (nuisance tripping) on your safety-kleen Washer, press the GFCI Test button, wait 5 seconds, and then press Reset.
  • K
    Karen BurkeSep 8, 2025
    What causes the pump to rattle on my safety-kleen 90?
    • E
      edwardperezSep 8, 2025
      If the pump is rattling on your safety-kleen Washer, replace the pump assembly (magnet issue).
  • D
    dennismartinSep 5, 2025
    What should I do if there is control box damage on my safety-kleen Washer?
    • A
      Amy LopezSep 5, 2025
      If the control box or GFCI of your safety-kleen Washer is damaged, the entire SK #2387 must be replaced. Do NOT open the control box!

Summary

1.0 INTRODUCTION

2.1 Applications

Details typical industries and parts cleaning applications for the washers.

2.2 Definitions

Defines key terms used in the manual for clarity and understanding.

2.3 Heater Pump Controller & Module

Describes the Heater Pump Controller (HPC) and Heater Pump Module (HPM) units.

3.0 SPECIFICATIONS

3.1 Technical Specifications

Provides detailed dimensions, weight, electrical, and operational specifications.

3.2 Site Requirements

Outlines necessary floor space, clearance, and power requirements for installation.

4.0 INSTALLATION

4.1 Tool Requirements

Lists essential tools needed for the proper installation of the equipment.

4.2 Unpacking

Instructions for carefully removing and inspecting all equipment components.

4.3 Pre-Installation Checks

Steps for verifying electrical outlet safety and wiring before installation.

4.4 Assembly Instructions

Step-by-step guide for assembling the parts washers.

5.0 TROUBLESHOOTING GUIDE

Lid and Fusible Link Issues

Addresses problems related to damaged lids and fusible links, including replacement.

No Power or Pump Operation Problems

Troubleshoots issues like no power, pump not working, or pump surging.

Lamp and Drainage Issues

Resolves problems with the lamp not turning on or drainage blockages.

Unit Leaks and Control Box Issues

Covers unit leaks, half moon damage, and control box problems.

6.0 REPAIR PROCEDURES

6.1 Tool Requirements

References external checklist for tools needed for repairs.

6.2 Pump Doesnt Work

Diagnoses and resolves issues where the pump is not functioning correctly.

7.0 LABEL PLACEMENT

8.0 PARTS LIST (Models 90, 91, 94)

9.0 MODEL 2387 PARTS LIST

safety-kleen 90 Specifications

General IconGeneral
Brandsafety-kleen
Model90
CategoryWasher
LanguageEnglish

Related product manuals