To Next Page
H
hmerrittSep 10, 2025
What to do if the half moon is damaged on my safety-kleen 91?
- WWilliam MossSep 10, 2025
If the tabs are broken or the half moon is lost on your safety-kleen Washer, replace it with SK #232037.
What to do if the half moon is damaged on my safety-kleen 91?
If the tabs are broken or the half moon is lost on your safety-kleen Washer, replace it with SK #232037.
What to do if the pump doesn’t work on my safety-kleen 91 Washer?
If the pump on your safety-kleen Washer isn't working, check the PUMP circuit breaker's ON/OFF position. Also, verify the power cord connection. Finally, make sure the electrical outlet is functioning correctly by plugging in another appliance or using an outlet tester.
How to resolve a drainage issue in my safety-kleen 91?
To address a drainage issue in your safety-kleen Washer, start by removing any debris from the crumb cup and/or strainer basket and dispose of it according to local regulations. You should also replace the filter sock.
What to do if there is fusible link damage in my safety-kleen 91?
To address fusible link damage on your safety-kleen Washer: Ensure the lid moves freely without obstruction and that the standpipe for the Model 90 (SK #2244) or the Model 94 (SK #2144) is in place and the locknut is tight. If the standpipe is loose, tighten the locknuts SK #5515 using an adjustable wrench. Remove any broken pieces of the old fusible link and replace it with a new one.
Why is my safety-kleen 91 leaking?
If your safety-kleen Washer is leaking, first check for any loose hoses that might be leaking on the floor and re-route them if necessary. If the drum or vat is leaking, replace them as soon as possible.
How to fix a lamp that doesn’t turn on in my safety-kleen Washer?
If the lamp on your safety-kleen Washer doesn't turn on, check the LAMP circuit breaker's ON/OFF position. Try turning the unit on and off again, ensuring the momentary switch always points down. Flip the On/Off switch on the lamp and push the Start/Stop button on the control box. Verify the power cord connection and ensure the electrical outlet is functioning. If needed, replace the bulb, using no more than a normal 40-watt bulb.
How to check customer outlet for power for safety-kleen 91 Washer?
Use an Outlet Tester to confirm proper wiring for your safety-kleen Washer.
How to stop lamp flashing (nuisance tripping) on my safety-kleen 91?
If the lamp is flashing (nuisance tripping) on your safety-kleen Washer, press the GFCI Test button, wait 5 seconds, and then press Reset.
What causes the pump to rattle on my safety-kleen 91?
If the pump is rattling on your safety-kleen Washer, replace the pump assembly (magnet issue).
What should I do if there is control box damage on my safety-kleen 91?
If the control box or GFCI of your safety-kleen Washer is damaged, the entire SK #2387 must be replaced. Do NOT open the control box!
Details typical uses and substances to avoid when cleaning.
Defines key technical terms and abbreviations used in the manual.
Describes the Heater Pump Controller (HPC) and Heater Pump Module (HPM) units.
Lists detailed dimensions, weight, electrical requirements, and operating temperatures.
Specifies space, clearance, power, and work area needs for installation.
Enumerate the tools necessary for setting up the parts washer.
Instructions for unpacking, inspecting for damage, and verifying electrical outlets.
Step-by-step procedures for assembling the sink-on-a-drum and vat models.
Directs users to a checklist for tools required for equipment repairs.
Addresses diagnosis and solutions for pump not powering on or having no flow.
Visual guide showing the placement of all operational and identification labels.
General| Brand | safety-kleen |
|---|---|
| Model | 91 |
| Category | Washer |
| Language | English |
