Salto CU5000 User Manual

All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any
item in this catalog, its design, construction, and/or materials.
P-200552 - -ED.04/05/2010
10 BASE - T
1
2
3
4
5
1
2
3
4
5
TAMPER
EXIT
BUTTON
DOOR
DETECTOR
READER 1
ENTRY
READER 2
EXIT
0 V.
+12 V.
NC
C
NO
NC
C
NO
RELAY 1
LOCKING
DEVICE
RS485
PERIPHERAL BUS
MAX. DIST. 100M
A
B
MODE
CRL
CLR
LED
COMM LED
ONLY IN CU50EN/SVN
SOLO EN CU50EN/SVN
TX/RX LED
Ethernet
10 BASE-T
LINK LED
RELAY 2
ALARMS
ON LED
ON
OFF
1 2 3 4
LECTOR 1
ENTRADA
LECTOR 2
SALIDA
SALIDA DESDE
EL INTERIOR
DETECTOR DE
PUERTA
BUS DE PERIFERICOS
R
S
4
8
5
RELE 2
ALARMAS
RELE 1
DISPOSITIVO
CIERRE
LED DE ALIMENTACION
LED DE ENLACE
LED DE COMUNICACION
Ethernet Patch Cable
ONLY CU50EN/SVN
IF NOT USED , DO NOT REMOVE THE JUMPER
CU5000
CU50EN/SVN
SI NO SE UTILIZA ,NO QUITE EL PUENTE
1
2
0
2
0
0
58
• Every time you connect or disconnect new hardware to the CU, please, press the CLR button once , so the CU
detects the new hardware. (beep).
• In case of connection to WR5000 or WR9001 readers , and when the sum of distances (Reader 1- CU) + (Reader 2-
CU) is longer than 100 meters, then , it is necessary not to connect wire 2 coming from one of the readers. Please,
use the other reader to connect with PPD.
• In case of inductive loads , use a varistor in a shunt connection with the load. A recommended varistor is supplied
having up to 24 V maximun (AC-DC).
• The maximun current of the contact to relay 1 and relay 2 is 16 A at 250 VAC with resistive loads and 12 A at
250 VAC with inductive loads.
• Siempre que conecte o desconecte nuevo hardware a la unidad de control, pulse una vez el botón CLR para que
la CU detecte el nuevo hardware. (pitido).
• En caso de conexión a lectores WR5000 o WR9001 , y cuando la suma de distancias (lector 1- CU) + (lector 2- CU)
sea superior a 100 metros, es necesario no conectar el hilo 2, procedente de uno de los lectores. Utilice el otro
lector para las conexiones con el PPD.
• En caso de carga inductiva, coloque el varistor en paralelo con la carga. Se suministra un varistor recomendado
de hasta 24 V máximo (AC-DC).
• La corriente máxima de los contactos en el rele 1 y rele 2 es de 16 A a 250 VAC con cargas resistivas y 12 A a 250
VAC con cargas inductivas.
Cable Ethernet para
red de área local.
SOLO CU50EN/SVN
Eng
E
NOTE: USE VARISTORS IN CASE
OF INDUCTIVE LOADS
NOTA: UTILIZAR VARISTORES EN
CASO DE CARGAS INDUCTIVAS
WIRE CONNECTIONS - CABLEADO
CONTROL UNIT - UNIDAD DE CONTROL
1/4

Salto CU5000 Specifications

General

Brand	Salto
Model	CU5000
Category	Control Unit
Language	English