OUTPUT XLR and 1/4" jack
Key Input Connector 1/4" jack
Key Output Connector 1/4" jack
Dimensions 1.5/8" (h) x 8.5/8" (w) 7 1/4" (d)
41.5 mm (h) x 215 mm (w) x 184 mm (d)
Net Weight 5.5lbs., (2.5 kg)
Shipping Weight 8lbs., (3.6 kg)
S•Direct Direct Box
Frequency Response 5-35 kHz, -3 dB
Noise Level (22-22kHz, Input Shorted) -104 dBu
THD + N (10 Hz -22 kHz) 0.013% typ. @ 1 VRMS,1 kHz.
Input Impedance (GTR) 1 Meg. Ohm
(SPK) 10 k Ohm
Max. Input Level (1% THD) +8.1 dBu ( 9v. Batt.)
+11.3 dBu (48v. Phantom)
GTR/SPK Input 1/4″ Phone Jack, unbalanced
OUTPUT/LINK 1/4″ Phone Jack, unbalanced
BALANCED OUTPUT XLR Connector, balanced
Phantom Power 24-48 VDC
Battery 9 Volt
Dimensions 2″ (h) x 5.6″ (w) x 4″ (d)
50.8mm (h) 142mm (w) x 101.6mm (d)
Weight 15 oz. • .43 Kg
S•Monitor Personal Monitor
Specifications TBD
S•Mix 5-channel Mixer
Specifications TBD
S•Amp 4-channel Headphone Amp
Specifications TBD
S•Convert +4 to -10dB/-10 to +4dB Converter
Specifications TBD
Mixers
MDR6
Frequency Response
Mic to Main 5 Hz - 54 kHz
Line to Main 5 Hz - 54 kHz
Aux Return to Main 5 Hz - 98 kHz
Line to Aux Send 5 Hz - 57 kHz
T.H.D. 0.02%
Residual Noise (30 kHz LPF, all control Min)
Main -89 dBu
Aux Send -86 dBu
Crosstalk (@ 1 kHz w/ 30 kHz LPF)
Ch vs. Ch 75 dB
Input vs. Output 87.5 dB
Peak LED Sensitivity (before clipping) 5 dB
CLIP Indicators Turn on: THD> 0.1%
Headphone output (600 ohm load) 100 mW
Maximum Input Level (1 kHz, ± 3dB)
Mic Input (Mono Ch) 10.5 dBu
Line Input (Stereo Ch) 7.6 dBu
Input Channel Equalizer (± 2dB)
High (shelving) 12 kHz ±15 dB
Mid (peaking) 2.5 kHz ± 15 dB
Low (shelving) 80 Hz ±15 dB
Meters 6 point LED meter (-20, -12, -6, 0, +6dB and PEAK)
Phantom Power +48V
Power Consumption 300W 1/8 power, 540W full
Dimensions (W x D x H) 2.7≤ (h) x 6.4≤ (w) x 9≤ (d)
69 mm (h) x 163 mm (d) x 228 mm (w)
Weight 4.5 lbs • 2.04 Kg
MDR8
Frequency Response (Trim @ Min, unity gain ± 3 dB)
Mic to Main 5 Hz - 54 kHz
Line to Main 5 Hz - 54 kHz
Aux Return to Main 5 Hz - 98 kHz
Line to Aux Send 5 Hz - 57 kHz
T.H.D. 0.02%
Residual Noise (30 kHz LPF, all control Min)
Main -89 dBu
Aux Send -86 dBu
Crosstalk (@ 1 kHz w/ 30 kHz LPF)
Ch vs. Ch 75 dB
Input vs. Output 87.5 dB
Peak LED Sensitivity (before clipping) 5 dB
CLIP Indicators Turn on: THD> 0.1%
Headphone output (600 ohm load) 100 mW
Maximum Input Level (1 kHz, ± 3dB)
Mic Input (Mono Ch) 10.5 dBu
Line Input (Stereo Ch) 7.6 dBu
Input Channel Equalizer (± 2dB)
High (shelving) 12 kHz ±15 dB
Mid (peaking) 2.5 kHz ± 15 dB
Low (shelving) 80 Hz ±15 dB
Meters 6 POINT LED METERS (-20, -12, -6, 0, +6dB and
PEAK)
Internal DSP Effects 24 BIT -8 presets: 1 - Large Hall; 2 Medium Hall,
3 - Large Room; 4 - Vocal Room 1; 5 - Vocal
Room 2; 6 - Chorus + Reverb; 7 - Chorus +
Delay; 8 - Stairwell
Phantom Power +48V
Power Consumption 300W 1/8 power, 540W full
Dimensions (W x D x H) 3 1/2≤ (h) x 11 1/2≤ (w) x 11 3/4≤ (d)
89 mm (h) x 292mm (w) x 299mm (d)
Weight 6.5 lbs. • (3 Kg)
MDR 10
Specifications TBD
MDR 16
Specifications TBD
Mixpad 4
Mic EIN: -128 dBu
Line EIN: -111 dBu
Frequency response: 10 Hz to 54 kHz
Total harmonic distortion (with 30 kHz LPF): .004%
EQUALIZATION
High (12 kHz): ±15 dB
Mid (2.5 kHz): ±12 dB
Low (80 Hz): ±15 dB
Battery operation: Three 9V alkaline
Dimensions: 2.7″ (h) x 6.4″ (w) x 9″ (d)
69 mm x (h) 163 mm (w) x 228 mm (d)
Weight: 1.85 lbs. • .839 kg.
Powered Mixers
TM300
MIXER/PREAMP SECTION
Frequency response (± 1 dB): <20 Hz to 20 kHz
Total harmonic distortion: < 0.02%
Graphic Equalizer: 7 band ±12 dB
Phantom power +48 V
POWER AMP SECTION
Maximum output power (1 kHz): 150 W per channel into 4 Ω
Total harmonic distortion: < 0.2%
Signal-to-noise ratio: >100 dB
Frequency response (± 3 dB): <12 Hz to 20 kHz
GENERAL
Power consumption: 780 w
Power requirements: 115 Vac • 50/60 Hz
230 Vac • 50 Hz
Dimensions: 5.5″ (h) x 19.35″ (w) x 13.75″ (d)
139 mm (h) x 349 mm (w) x 491 mm (d)
Weight: 29.7 lbs. • 13.5 kg
TM500
MIXER/PREAMP SECTION
Frequency response (± 1 dB): <20 Hz to 20 kHz
Total harmonic distortion: < 0.02%
Graphic Equalizer: 7 band ±12 dB
Phantom power +48 V
POWER AMP SECTION
Maximum output power (1 kHz): 250 W per channel into 4 Ω
Total harmonic distortion: < 0.2%
Signal-to-noise ratio: >100 dB
Frequency response (± 3 dB): <12 Hz to 20 kHz
GENERAL
Power consumption: 1100 w
Power requirements: 115 Vac • 50/60 Hz
230 Vac • 50 Hz
Dimensions: 5.5″ (h) x 19.35″ (w) x 13.75″ (d)
139 mm (h) x 349 mm (w) x 491 mm (d)
Weight: 36 lbs. • 16.4 kg
PA324
Rated Output power 150W/4Ω@0.5% THD at 1KHz per amplifier
Frequency response 20Hz~20KHz±0.5dB@1W Output into 8Ω (AMP
OUT)
20 Hz~20KHz ±0.5@+4dB Output into 10Ω
(MAIN OUT, MONITOR OUT, EFX SEND)
Total Harmonic Distortion < 0.1%@20Hz~20KHz, 75W output into4Ω
(AMP OUT)
Less than 0.1%@20 Hz~20KHz+14dB output into
10KΩ (MAIN OUT, MON OUT, EFX SEND)
Hum & Noise -121dB equivalent input noise
(Average, RS+150Ω) -100dB residual output noise (MAIN OUT, MONI-
TOR OUT, EFX OUT)
(with 20Hz~20KHz BPF) -79dB (MAIN OUT, MONITOR OUT) Master level
control at maximum all channel level control at
minimum.
-79dB (EFX OUT) Master level control at maxi
mum all channel level controls at minimum
Crosstalk 1KHz 70dB adjacent input, 70dB input to output
Input Channel Equalization
HIGH 12KHz shelving (± 15dB Maximum)
MID 2.5KHz peaking (± 12dB Maximum)
LOW 80Hz shelving (± 15dB Maximum)
Meters 7 POINT LED METERS (-20, -10, -7, -4, 0, +3, +6dB)
Graphic Equalizer 7 bands (63, 160, 400, 1K, 2.5K, 6.4K, 16KHz)
Internal DSP Effects 24 BIT - 8
Dimensions 19.25″ (w) x 11.25″ (h x 11.4″ (d)
489mm (w) x 286mm (h) x 289mm (d)
Weight 32.3 lbs.•14.7Kg
Power Distribution & Rack Gear
S Patch Plus 48 Channel, fully Balanced patchbay
Channel 48
Switchable configuration modes Normal, Half-normal and Thru
Dimensions 1 3/4″ (h) x 19″ (w) x 3″ (d)
44.45 mm (h) x 482.6 mm (w) x 76.2 (d)
Weight 3.8 lbs. • (1.72 Kg)
PowerBrite Pro7/Pro9
Number of Outlets
Pro7: 6 switched, 1 unswitched
Pro9: 8 switched, 1 unswitched
Max. Current: Pro7 15 Amps/Pro9 10 Amps
Input Voltage (RMS): Pro7 130 Vac/Pro9 245 Vac
Spike Protection Mode: Hot to Neutral, Hot to Ground,
and Neutral to Ground
Max. Clamping Voltage (@ 50 A): 700 Vac
Response Time: 1 nanosecond
Max. Surge Current: 4,500 Amps (8 x 20 ms pulse)
Max. Spike Energy: 104 Joules
Noise Attenuation: > 20 dB, 1.5 MHz to 200 MHz
AC Inlet: PS9 North America/PS11 IEC
Lamp/Starter: Fluorescent F45CW condenser type FS2
Lamp Life: 3000 hours 95 Lumens
Starter Fuse (Internal): 500 ma T type
Dimensions: 1.75″ (h) x 19″ (w) x 7.5″ (d)
44 (h) x 482 mm (w) x 190 (d)
Weight: 7 lbs. • 3.2 kg
Conforms: UL/CUL/CE/LVD
PowerBrite PB9/PB11
Number of Outlets
PB9: 8 switched, 1 unswitched
PB11: 10 switched, 1 unswitched
Max. Current: PB9 15 Amps/PB11 10 Amps
Input Voltage (RMS): PB9 130 Vac/PB11 245 Vac
Spike Protection Mode: Hot to Neutral, Hot to Ground,
and Neutral to Ground
Max. Clamping Voltage (@ 50 A): 700 Vac
Response Time: 1 nanosecond
Max. Surge Current: 4,500 Amps (8 x 20 ms pulse)
Max. Spike Energy: 104 Joules
Noise Attenuation: > 20 dB, 1.5 MHz to 200 MHz
AC Inlet: PS9 North America/PS11 IEC
Lamp/Starter: Fluorescent F45CW condenser type FS2
Lamp Life: 3000 hours 95 Lumens
Starter Fuse (Internal): 500 ma T type
Dimensions: 1.75″ (h) x 19″ (w) x 7.5″ (d)
44 (h) x 482 mm (w) x 190 (d)
Weight: 7 lbs. • 3.2 kg
Conforms: UL/CUL/CE/LVD
PowerStrip PS9/PS11
Number of Outlets
PS9: 8 switched, 1 unswitched
PS11: 10 switched, 1 unswitched
Max. Current: PS9 15 Amps/PS11 10 Amps
Input Voltage (RMS): PS9 130 Vac/PS11 245 Vac
Spike Protection Mode: Hot to Neutral, Hot to Ground,
and Neutral to Ground
Max. Clamping Voltage (@ 50 A): 700 Vac
Response Time: 1 nanosecond
Max. Surge Current: 4,500 Amps (8 x 20 ms pulse)
Max. Spike Energy: 104 Joules
Noise Attenuation: > 20 dB, 1.5 MHz to 200 MHz
AC Inlet: PS9 North America/PS11 IEC
Dimensions: 1.75″ (h) x 19″ (w) x 7.5″ (d)
44 (h) x 482 mm (w) x 190 (d)
Weight: 7 lbs. • 3.2 kg
Conforms: UL/CUL/CE/LVD
Audio Equipment
Resolv 50a
Rated Output Power
Low frequency amp: 50 watts @1K into 4ohms
High frequency amp: 25 watts @ 10K into 4ohms
Frequency Response:
Low amp: tbd
High amp: tbd
Distortion THD: tbd
Power consumption: 75 watts
Frequency response: tbd
Driver: 5.25" Woofer Shielded
Tweeter: 1″ Dome Shielded
Dimensions: tbd
Weight: tbd
Resolv 65a
Rated Output Power
Low frequency amp: 75 watts @1K into 4ohms
High frequency amp: 30 watts @ 10K into 4ohms
Frequency Response:
Low amp: 40hz-3200
High amp: 3200-50K
Distortion THD: <.05%
Power consumption: 150 watts
Frequency response: 40 Hz to 20 kHz
Driver: 6 1/2" Woofer Shielded
Tweeter: 1″ Dome Shielded
Dimensions: 13 5/8"(H) x 8 1/2" (W) x 9 7/8" (D)
Weight: 18 lbs. • 8.2 kg
Resolv 65
Power Rating: 75 watts
Impedance: 8 ohm
Frequency response: 40 Hz to 20 kHz
Driver: 6 1/2″ Woofer Shielded
Tweeter: 1″ Dome Shielded
Dimensions: 13 5/8"(H) x 8 1/2" (W) x 9 7/8" (D)
Weight: 13.4 lbs. • 6.1 kg
Resolv 80a
Rated Output Power
Low frequency amp: 75 watts @1K into 4ohms
High frequency amp: 25 watts @ 10K into 4ohms
Frequency Response:
Low amp: tbd
High amp: tbd
Distortion THD: tbd
Power consumption: 100 watts
Frequency response: tbd
Driver: 8" Woofer Shielded
Tweeter: 1″ Dome Shielded
Resolv Sub 120
Amp: 120watts into 4ohms
Frequency Response: 30hz-150
Distortion THD: <.05%
Power consumption: 210 watts
Driver: 10″ long stroke
Dimensions: 14 1/2″ (H) x 14 1/2″ (W) x 17.5″ (D)
Weight: 39 lbs. • 17.75 kg
Expedition Express
Power Rating: (@ 8Ω): 250 Watts Program
Frequency Response: 60 Hz – 15 kHz ± 3 dB
Sensitivity: 97 dB SPL @ 1W/1m
Crossover Frequency: 2.3 kHz (12 dB Per Octave)
LF Driver: 12≤ heavy-duty driver ,
2.5≤ voice coil (Kapton Former),
50 oz. barium ferrite magnet
HF Driver: 1≤ titanium compression driver
Stereo Mixer Section:
Inputs 2 Mic/Line XLR/TRS,
1 Stereo Line w/Mic XLR
Frequency Response 10 Hz - 50 kHz
Crosstalk 70 dB @ 1 kHz
Equalization Frequencies 100 Hz (Low), 10 kHz (High)
Effects DSP Reverb with 6 Presets
Mounting: Integral 1 3/8≤ Pole Mount Receptacle, Fly Points
Dimensions: EX250m and EX250e 21 1/4 (h) x 14 5/8 in. (w) x 17 3/8 (d)
539 mm (h) x 371 mm (w) x 441 (d)
Weight:
EX250e 28.5 lbs • 12.9 kg
EX250m 45.0 lbs • 20.4 kg
XP100
Power Rating: 250 Watts Program; 400 Watts Max. Peak
Frequency Response 60 Hz – 15 kHz
Sensitivity 97 dB SPL @ 1W/1m
Crossover Frequency 2.3 kHz (24 dB Per Octave)
LF Driver 12″ heavy-duty driver
2.5″ voice coil (Kapton Former)
To Next Page
Loading...
