Samsung AM360KXVAGH1ET - Page 51

51
ENGLISH
AЇϩϩ˝ͱθѤɇθ˝ϩ˵ʪΧΧʪϑ
1. Make sure that you prepared the required tools.
 ťΧʪʀЇϩϩʪθࡥUʪɵЇθθ˝ϩͱͱࡥѤɇθ˝ϩͱͱɇʒΧΧʪ˵ͱʒʪθࡥʪϩʀ࢏
2. Ã˙цͱЇиɇϩϩͱϑ˵ͱθϩʪϩ˵ʪΧΧʪࡥʀЇϩϩиϩ˵ɇΧΧʪʀЇϩϩʪθʪϑЇθ˝ϩ˵ɇϩϩ˵ʪʀЇϩʪʒ˝ʪθʪɇϑɇϩ߫ߢঌиϩ˵ϩ˵ʪ
side of the pipe.
 Refer to below illustrations for correct and incorrect examples of cut edges.
߫ߢঌ
Oblique Rough Burr
3. To prevent a gas leak, remove all burrs at the cut edge of the pipe using a Deburring tool.
4. AɇθθцͱЇϩѤɇθ˝иͱθЇϑ˝Ѥɇθ˝ϩͱͱɇϑϑ˵ͱиɵʪͱи࢏
A
Flaring bar
Pipe
Yoke
Flaring bar
Pipe
Flare nut
Clutch type Wing nut type
[Flaring tools]
Pipe diameter
[D (mm)]
UʪΧϩ˵ͱ˙Ѥɇθ˝Χɇθϩࣈ࣑࣒ࣉ
Ƹϑ˝Ѥɇθ˝ϩͱͱ˙ͱθ
R-410A
Ƹϑ˝ʀͱЭʪϩͱɇѤɇθ˝ϩͱͱ
Clutch type Wing nut type
Ø 6.35 ߢߢ࢏ߧ ߣ࢏ߢߣ࢏ߧ ߣ࢏ߧߤ࢏ߢ
Ø 9.52 ߢߢ࢏ߧ ߣ࢏ߢߣ࢏ߧ ߣ࢏ߧߤ࢏ߢ
Ø 12.70 ߢߢ࢏ߧ ߣ࢏ߢߣ࢏ߧ ߣ࢏ߧߤ࢏ߢ
Ø 15.88 ߢߢ࢏ߧ ߣ࢏ߢߣ࢏ߧ ߣ࢏ߧߤ࢏ߢ
5. A˵ʪʀϩ˵ɇϩцͱЇѤɇθʪʒϩ˵ʪΧΧʪʀͱθθʪʀϩц࢏
 ŵʪ˙ʪθϩͱɵʪͱиЇϑϩθɇϩͱϑ˙ͱθʀͱθθʪʀϩɇʒʀͱθθʪʀϩʪуɇΧʪϑͱ˙ѤɇθʪʒΧΧʪ࢏
Uneven ThicknessCrackedDamaged SurfaceInclinedCorrect
࡛If foreign matters or burrs are not removed after cutting pipe, refrigerant gas may leak.
࡛If foreign matters enter inside the pipe, important interior parts of the unit may get damaged
ͱθΧθͱʒЇʀϩʪ˙ѣʀʪʀциɵʪθʪʒЇʀʪʒ࢏Ɗͱࡥϩ˵ʪʒθʪʀϩͱͱ˙ΧΧʪϑ˵ͱЇʒɵʪʒͱииɇθʒʒЇθ˝ΧΧʪ
ʀЇϩϩ˝ͱθѤɇθ˝࢏
CAUTION