To Next PageTo Next PageWhat causes absolute value system shutdown error in Samsung CP Industrial Equipment?
If your Samsung Industrial Equipment shows an absolute value system shutdown error, it is because the encoder power is off. To fix this, connect the battery and clear the absolute value encoder.
How to resolve position limit exceeding error on Samsung CP Industrial Equipment?
If you are experiencing a position limit exceeding error on your Samsung Industrial Equipment, it is likely because the motor does not move in accordance with the command pulse. To solve this, adjust the gain and reduce the load.
General| Manufacturer | Samsung |
|---|---|
| Series | CP Series |
| Display Type | LCD |
| Resolution | Full HD (1920x1080) or higher depending on model |
| Viewing Angle | Wide viewing angle |
| Durability | Built to withstand harsh industrial environments |
| Mounting Options | VESA Mount |
| Input Ports | HDMI, VGA |
| Operating Temperature | 0°C to 50°C (depending on model) |
Important safety notice regarding machine operation and user training.
Essential safety rules for operation, maintenance, and symbol meanings.
Identification and description of safety labels on the front of the machine.
Identification and description of safety labels on the rear of the machine.
Details on what is covered by the warranty and common exclusions.
Overview of the different sections and their content within the manual.
Explanation of symbols used for referencing and memos in the manual.
Guide to understanding chapter titles, figure numbering, and page references.
Definitions for various components like Nozzle, Holder, Spindle, and Vision System.
Steps to follow before and after performing maintenance tasks.
Requirements for air pressure and power input voltage.
Lists and descriptions of tools included in the cleaning kit and other provided tools.
Procedure for inspecting and cleaning machine nozzles.
Checking the nozzle holder tube for looseness or cracks.
Inspection of the flying vision mirror for dust or contamination.
Procedure for cleaning debris from the feeder station slots.
Inspection of the stage camera cover glass for dust or foreign matter.
Steps for cleaning the camera lens and LED components.
Checking and adjusting the machine's pneumatic pressure.
Checking the nozzle holder for potential bending due to improper operation.
Inspection of the vacuum filter for contamination by dust or solder paste.
Inspection of the spindle for contamination that may cause pickup problems.
Checking the X-Y frame cableveyor for wear and tear.
Inspection of the PCB conveyor belt for tension, wear, and shifting.
Checking PCB sensors for contamination and adjusting sensitivity.
Checking the operation accuracy of the ANC shutter sensor.
Verifying feeder installation status to prevent emergency stops.
Checking the cooling fan filter for contamination.
Checking head section for contamination and coil tubes for twist/leakage.
Checking head air module pressure and flying vision lens contamination.
Checking X-Y frame for contamination and proper operation.
Checking the operation of X-Y frame limit and home sensors.
Checking the operation status and sensors of machine cylinders.
Inspecting the stopper end for wear on the PCB connection face.
Checking the feeder station cylinder for smooth operation.
Adjusting cylinder speed and inspecting air filters.
Checking cooling fan operation and cleaning dust from the control rack.
Reference for lubrication and grease application procedures.
Table detailing lubrication types, methods, and periods for components.
Specific lubrication procedures for the head assembly.
Lubrication procedures for X-axis LM guide rails and ball screws.
Inspection of Y-axis LM guide rails and ball screws for lubrication.
Lubrication procedures for conveyor width adjustment mechanisms.
Inspection of the conveyor chain for lubrication and contamination.
Definition of consumables and their recommended replacement intervals.
Troubleshooting guide for identifying and resolving machine noise issues.
Procedures for inspecting power supply status and switch functions.
Checking PC component installation and cable connections in the controller rack.
Checking the video card's status and connection for proper operation.
Procedures for HDD detection, including CMOS setup adjustments.
Checking the FDD's power supply and cable connections.
Checking keyboard, mouse, and machine controller assembly status.
List of control boards and their part numbers and remarks.
Description of CAN Master Board functions and its connections.
Description of Head Control Board functions and required power supply.
Description of Conveyor Control Board functions and required power supply.
Description of Feeder Control Board functions and required power supply.
Description of Illumination Control Board functions and required power supply.
Checking the X-axis motor drive for normal operation.
Jumper settings for EPROM booting and System Controller.
Jumper settings for XY and H1/2 axis boards.
Jumper settings for H3/4 and H5/6 axis boards.
Jumper settings for CAN Master and Step I/F boards.
Digital switch settings for AC Servo Drivers.
Troubleshooting for motor control voltage and overvoltage alarms.
Troubleshooting for power source voltage and overcurrent alarms.
Troubleshooting for encoder and overtravel related alarms.
Troubleshooting for limit exceeding and overspeed alarms.
