Samsung DB40E User Manual (English)

To Next Page

Quick Setup Guide

- The colour and the appearance may differ depending on the product, and the specifications

are subject to change without prior notice to improve the performance.

- Recommended hours of use per day for the DBE models is less than 16 hours. If the product is

used for longer than 16 hours a day, the warranty may be void.

- Download the user manual from the website for further details.

http://www.samsung.com/displaysolutions

DB32E DB40E DB48E DB55E

DM32E

BN6807244J03

The terms HDMI and HDMI High-Definition Multimedia Interface, and the

HDMI Logo are trademarks or registered trademarks of HDMI Licensing

LLC in the United States and other countries.

Reverse Side

RGB IN RJ45

RS232C IN

RS232C OUT

AUDIO OUT

USB

HDMI IN

DVI /

MAGICINFO IN

RGB / DVI /

HDMI / AV /

COMPONENT

AUDIO IN

SD CARD

COMPONENT IN

2 3 4 5

6 7 8

0 !

1 Connects to MDC using an RS232C adapter.

- For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available on the website.

2 Receives sound from a PC via an audio cable.

3 Outputs sound to an audio device via an audio cable.

4 Connect to an SD memory card.

5 Connect to a USB memory device.

6 DVI: Connects to a source device using a DVI cable or HDMI-DVI cable.

MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box (sold separately).

7 Connects to a source device using an HDMI cable.

8 Connects to a source device using the AV/Component adapter.

9 Supplies power to the external sensor board or receives the light sensor signal.

0 Connects to a source device using a D-SUB cable.

! Connects to MDC using a LAN cable.

Issues Solutions

The screen keeps

switching on and off.

Check the cable connection between the

product and PC, and ensure the connection is

secure.

No Signal is displayed

on the screen.

Check that the product is connected correctly

with a cable.

Check that the device connected to the

product is powered on.

Not Optimum Mode is

displayed.

This message is displayed when a signal

from the graphics card exceeds the product’s

maximum resolution and frequency.

Refer to the Standard Signal Mode Table and

set the maximum resolution and frequency

according to the product specifications.

The images on the

screen look distorted.

Check the cable connection to the product.

The screen is not clear.

The screen is blurry.

Adjust Coarse and Fine.

Remove any accessories (video extension

cable, etc) and try again.

Set the resolution and frequency to the

recommended level.

The screen appears

unstable and shaky.

Check that the resolution and frequency of the

PC and graphics card are set within a range

compatible with the product. Then, change the

screen settings if required by referring to the

Additional Information on the product menu

and the Standard Signal Mode Table.

There are shadows or

ghost images left on the

screen.

Issues Solutions

The screen is too bright.

The screen is too dark.

Adjust Brightness and Contrast.

Screen colour is

inconsistent.

Go to Picture and adjust the Colour Space

settings.

White does not really

look white.

Go to Picture and adjust the White Balance

settings.

There is no sound. Check the connection of the audio cable or

adjust the volume.

Check the volume.

The volume is too low. Adjust the volume.

If the volume is still low after turning it up to

the maximum level, adjust the volume on

your PC sound card or software programme.

The remote control does

not work.

Make sure that the batteries are correctly in

place (+/-).

Check if the batteries are flat.

Check for power failure.

Make sure that the power cord is connected.

Check for any special lighting or neon signs

switched on in the vicinity.

Troubleshooting Guide

Checking the Components

Control Panel

DB32E DM32E

Contact the vendor where you purchased the product if any

components are missing.

Speaker

Power on the product.

If you press the button when the product is turned on, the control

menu will be displayed.

Move to the upper or lower menu. You can also adjust the value of an option.

Move to the left or right menu.

Remote sensor

Press a button on the remote control pointing at the sensor on the

front of the product to perform the corresponding function.

Quick Setup Guide

Warranty card

(Not available in some locations)

Power cord

Batteries

(Not available in some

locations)

Remote Control D-SUB cable

RS232C(IN) adapter

AV/Component

adapter

AUDIO adapter

COVER-JACK

Screw (M3L8, 1EA)

(M4L8, 4EA)

BN68-07244J-03_QSG_DBE DM32E_INDIA_ENG.indd 1 2019-06-28 오전 11:08:42

Need help?

Do you have a question about the Samsung DB40E and is the answer not in the manual?

Samsung DB40E Specifications

General

Panel life	- h
Color gamut	72 %
Pixel pitch	0.15375 x 0.46125 mm
Touchscreen	-
Response time	8 ms
Display diagonal	40 \
Display brightness	350 cd/m²
Display technology	LED
Native aspect ratio	16:9
Vertical scan range	48 - 75 Hz
Horizontal scan range	30 - 81 kHz
LED backlighting type	Direct-LED BLU
Contrast ratio (dynamic)	50000:1
Contrast ratio (typical)	5000:1
Display number of colors	16.78 million colors
Display diagonal (metric)	101 cm
Active display area (W x H)	885.6 x 498.15 mm
Supported graphics resolutions	1920 x 1080 (HD 1080)
USB version	2.0
Ethernet LAN	Yes
Operating hours (hours/days)	16/7
Product color	Black
Product design	Digital signage flat panel
Bezel width (side)	9.5 mm
Bezel width (bottom)	15 mm
Panel mounting interface	200 x 200 mm
RMS rated power	20 W
Number of built-in speakers	2
AC input voltage	100 - 240 V
Heat dissipation	1407.8 BTU/h
AC input frequency	50 - 60 Hz
Power consumption (max)	121 W
Power consumption (standby)	0.5 W
Power consumption (typical)	76 W
System on Chip (SoC) type	Samsung SMART Signage Platform (SSSP) Gen 3
Dot clock scanning frequency	148.5 MHz
Sustainability certificates	ENERGY STAR
Computer system type	System on Chip (SoC)
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 80 %
Package depth	138 mm
Package width	1012 mm
Package height	605 mm
Package weight	9100 g
Certification	FCC (USA) Part 15, Subpart B Class A, CE (Europe) : EN55022:2006+A1:2007, EN55024:1998+A1:2001+A2:2003, VCCI (Japan) : VCCI V-3 /2010.04 Class A, KCC/EK (Korea) : Tuner : KN13 / KN20, Tunerless : KN22 / KN24, BSMI (Taiwan) : CNS13438 (ITE EMI) Class A / CNS13439 (AV EMI) / CNS14409 (AV EMS) / CNS14972 (Digital), C-Tick (Australia) : AS/NZS CISPR22:2009, CCC(China) :GB9254-2008, GB17625.1-2012, GOST(Russia/CIS) : GOST R 51317 Series, GOST 22505-97, EN55022:2006+A1:2007, EN55024:1998+A1:2001+A2:2003 CB (Europe) : IEC60950-1/EN60950-1, CCC (China) : GB4943.1-2011, PSB (Singapore ) : PSB+IEC60950-1, NOM (Mexico ) : NOM-001-SCFI-1993, IRAM (Argentina ) : IRAM+IEC60950-1, SASO (Saudi Arabia ) : SASO+IEC60950-1, BIS(India) : IEC60950-1 / IS13252, NOM(Mexico) : Tuner : NOM-001-SCFI-1993, Tunerless : NOM-019-SCFI-1998, KC(Korea) : K 60950-1, EAC(Russia) : EAC+IEC60950-1, INMETRO(Brazil) : INMETRO+IEC60950-1, BSMI(Taiwan) : BSMI+IEC60950-1, RCM(Australia) : IEC60950-1/AS/NZS 60950-1, CSA (Canada) : cUL, UL(USA) : cUL60950-1, TUV (Germany) : CE, NEMKO (Norway) : CE