Samsung DV400EWHDWR/AA User Manual (English)

Other manuals for Samsung DV400EWHDWR/AA

Service Manual50 pages

Technical Information12 pages

Questions and Answers:

J
Jenna PageAug 14, 2025
Why does my Samsung DV400EWHDWR/AA Dryer not start?
- Z
  zjohnsonAug 14, 2025
  If your Samsung Dryer won't start or run, make sure all wires are correctly connected to their terminals and that the dryer is properly plugged in. Check for a blown fuse or tripped circuit breaker. Ensure the door switch is functional and the door is fully closed. Verify the start/pause rotary selector dial is working and the control board is operational. Additionally, check if the belt is off or broken, which could activate the belt cut-off switch. Confirm the drive motor is functional and check the motor winding resistance: it should be 2.88 ohms between pin #3 and 4, and 3.5 ohms between pin #4 and 5. Finally, check for error code 3.
A
Adam MorrisAug 17, 2025
Why does my Samsung Dryer run for a few minutes and then stop?
- M
  Megan MayAug 17, 2025
  If your Samsung Dryer runs for a few minutes and then stops, there might be lint buildup around the drive motor. Other potential causes include low voltage, a blocked blower impeller in the blower housing, or start switch contacts stuck closed in the drive motor.
G
gatespaulAug 20, 2025
Why is my Samsung DV400EWHDWR/AA Dryer so noisy?
- L
  Larry MillerAug 20, 2025
  If your Samsung Dryer is noisy or vibrating, investigate the following: For thumping sounds, check for a loose tumbler baffle, worn or misaligned rear tumbler rollers, an out-of-round tumbler, or a high weld seam on the tumbler. For ticking sounds, look for a loose wire harness or an object caught in the blower wheel area. Scraping sounds could indicate a front or rear bulkhead felt seal out of position or worn tumbler front bearings. Roaring sounds might mean the blower wheel is rubbing on the blower housing or the motor bearings are bad. A popping or squealing sound could suggest a sticky or frayed belt.
C
Cameron MendozaAug 23, 2025
Why is my Samsung DV400EWHDWR/AA not drying clothes properly?
- E
  echerryAug 25, 2025
  If your Samsung Dryer is causing improper drying, leading to wrinkled clothes, rough texture, or long dry times, ensure the lint filter is clean. Check for any restrictions in the exhaust system, including a stuck outside exhaust hood damper door. The exhaust might be too long, have too many elbows, or use flex ductwork. Also, ensure the dryer has sufficient intake air. Other factors could be an incorrect tumbler speed, a slipping tumbler belt, a bound blower impeller (check for foreign material), overloading the dryer, incorrect fabric settings, or clothes that are too wet due to insufficient washer spin.
E
Elizabeth HoodAug 27, 2025
What causes the igniter to not glow in my Samsung DV400EWHDWR/AA?
- M
  Michael WilliamsAug 27, 2025
  If the igniter in your Samsung Dryer does not glow, it could be due to an open flame sensor or an open igniter. Other potential causes include a shorted booster coil, open wiring, a bad motor switch (neutral supply), or no power from the control (L1 supply).
L
Leonard PriceAug 30, 2025
Why is the gas not igniting in my Samsung DV400EWHDWR/AA Dryer even though the igniter glows?
- M
  Megan LopezAug 30, 2025
  If the igniter glows in your Samsung Dryer but there's no gas ignition, it could be due to an open secondary coil or an open holding coil. Other potential causes include an open wire harness or a stuck flame sensor (stuck closed).
B
benjaminsmithSep 2, 2025
Why does the flame go out after ignition in my Samsung DV400EWHDWR/AA?
- S
  Sandra WilliamsSep 2, 2025
  If the gas ignites in your Samsung Dryer but the flame goes out, the radiant sensor contacts might be opening prematurely. Alternatively, a weak gas valve coil may open when stressed by higher temperatures. Other potential causes include a weak hi-limit, poor venting, or bad drum seals.
R
Robert StewartSep 6, 2025
What to do if my Samsung DV400EWHDWR/AA Dryer blows fuses?
- Z
  zkimSep 6, 2025
  If your Samsung Dryer blows fuses or trips the circuit breaker, verify that the belt is well connected and that the motor winding is continuous (rotor winding, stator winding, generator). Also, check if the motor protector is functioning normally. If these checks do not reveal any issues, the PCB assembly may be faulty and require replacement.
R
Rhonda MooreSep 9, 2025
Why does my Samsung gas dryer keep tripping the breaker?
- S
  Susan HowardSep 9, 2025
  If your Samsung gas model dryer blows fuses or trips the circuit breaker, it's important to understand that the dryer draws a certain amperage during ignition and when the burner is on. If the dryer is drawing more amperage than specified, the issue might be with the house wiring, fuse box, or circuit breaker. Other potential causes include a loose igniter harness shorted to the base, incorrect wiring or a wire shorted to ground, or a drive motor winding shorting to ground.

Samsung DV400EWHDWR/AA Specifications

General

Type	Electric
Color	White
Drum Material	Stainless Steel
Voltage	240V
Ventless	No
Wrinkle Care	Yes
Moisture Sensor	Yes
Energy Star Certified	Yes
Width	27"
Height	38 11/16 in