on
if?'.~
Software
Upgrade
HD
Connection
Guide
Contact
Sam
sung
INPUT
I
SUPPORT
•
Configuring
the
Input
Menu
U
Source
List
Use to select TV
or
other external input sources such
as
DVD I Blu-ray players I Cable Box I
Satellite receivers (Set-Top Box) connected to the
TV
Use to select the input source of your
choice
('51
Press the SOURCE button
on
the remote control
to
view
an
external signal source.
TV,
AV1, AV2, Component1,
Component2,
PC, HDMIIDVI, HDMI2, HDMI3 (LN52B530)
TV,
AV,
Component,
PC, HDMIIDVI, HDMI2, HDMI3 (LN32B530, LN37B530, LN40B530,
LN46B530)
f2
You
can choose only those external devices that are connected
to
the
TV.
In
the Source
List, connected inputs will be highlighted and sorted to the top Inputs that are not
connected will be sorted to the bottom.
fB
Using the
Color
buttons
on the remote
with
the Source
list
-
Red
(Refresh) Refreshes the connected external devices. Press this if your Source
is
on
and connected, but does not
appear
in
the list.
- TOOLS (Tools) Displays the
Edit
Name and
Information
menus
:-J
Edit
Name
Name the device connected
to
the input jacks to make your input source selection easier.
VCR
I DVD I Cable STB I Satellite STB I PVR STB I
AV
Receiver I Game I
Camcorder
I
PC
I DVI
PC
I
DVII
TV
IIPTV
I Blu-ray
I
HD
DVD I DMA
fE)
When a
PC
with a resolution of 1920 X 1080@60Hz
is
connected
to
the
HDMIIN
1 port, you should set the HDMI1IDVI mode
to DVI
PC
in
the
Edit
Name of the
Input
mode.
•
Configuring
the
Support
Menu
U
Self
Diagnosis
Picture Test
If you think you have a picture problem, perform the picture test. Check the color pattern
on
the
screen to see if the problem still exists.
• Yes: If the test pattern does not appear or there
is
noise
in
the test pattern, select Yes.
There may
be
a problem with the
TV
Contact Samsung's call center for assistance.
• No If the test pattern
is
properly displayed, select No. There may
be
a problem with your
external equipment. Please check your connections. If the problem still persists, refer to
the external device's user manual.
.~
Sound
Test
If
you think you have a sound problem, please perform the sound test.
You
can check the
sound
by
playing a built-in melody sound through the
TV
'Does the problem still exist with this sound test?· appears
on
the screen
If
you
hear
no
sound from the TV's speakers, before performing the sound test, make sure Speaker Select
is
set
to
TV
speaker
in
the Sound menu.
The melody will
be
heard during the test even if Speaker
Select
is
set
to
External Speaker or the sound
is
muted
by
pressing
the MUTE button.
• Yes: If during the sound test you can hear sound only from one speaker or not at all, select Yes. There may
be
a problem with
the
TV
Contact Samsung's call center for assistance.
• No: If you can hear sound from the speakers, select No. There may be a problem with your external equipment. Please check
your connections If the problem still persists, refer
to
the external device's user manual.
Signal
Strength
(digital
channels
only)
Unlike analog channels, which can vary
in
reception quality from
'snowy'
to
clear, digital (HDTV) channels have either perfect
reception quality or you will not receive them at all.
So,
unlike analog channels, you cannot fine tune a digital channel.
You
can.
however, adjust your antenna to improve the reception of available digital channels.
If the signal strength meter indicates that the signal
is
weak, physically adjust your antenna
to
increase the signal strength.
Continue to adjust the antenna until you find the best position with the strongest signal.
To Next Page
Loading...
