Quick Setup Guide
QP82R-8K
* Recommended hours of use per day of this product is under 16 hours. If the product is
used for longer than 16 hours a day, the warranty may be void.
* The colour and the appearance may differ depending on the product, and the content in
the manual is subject to change without prior notice to improve the performance.
* Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
BN68-09675B-00
Checking the Components Connecting the product to the One Connect
Contact the vendor where you purchased the product if any components are missing.
The pictures may look different from the actual components.
Quick Setup Guide
Warranty card
(Not available in some
locations)
Batteries (AAA x 2)
(Not available in some
locations)
Remote Control RS232C adapter
Holder-Ring
(For Wall Mount) x 4
Stand / Screw (M4 x L14) x 4
One Connect One Connect Power Cable
One Invisible Connection /
Screw (M4 x L12)
HOLDER-CABLE Bending Cover
Parts
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
1 Remote sensor
Press a button on the remote control pointing at the bottom of
the product face to perform the function. The remote control
sensor is located on the bottom of the product.
* Using other display devices in the same space as the remote
control of this product can cause the other display devices to be
inadvertently controlled.
2 Control button
ꞏ
button: Turns the product on.
- Press
button: Display the Control menu. / Select or run a
focused item on the menu.
- Press and hold
button: The running function is terminated.
ꞏ Up/Down/Left/Right Button: Move the menu.
ꞏ Left/Right Button: Changes the volume.
3 Control menu
ꞏ
Home: Enter MagicInfo or URL Launcher mode.
ꞏ
Settings: Display the OSD menu.
ꞏ
Return: Exit the control menu.
ꞏ
Source: Select the connected input source.
ꞏ
Power off: Power off the product.
4 Power indicator
Speaker
Issues Solutions
The screen keeps
switching on and off.
Check that the cable between the product
and the PC is connected correctly.
No Signal is
displayed on the
screen.
Check that the product is connected
correctly with a cable.
Check that the source device connected to
the product is powered on.
Depending on the type of external device,
the screen may not display properly. In this
case, connect it with the HDMI Hot Plug
function turned On.
Not Optimum Mode
is displayed.
This message is displayed when a
signal from the graphics card exceeds
the product’s maximum resolution and
frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
The images on the
screen look distorted.
Check the cable connection to the product.
The screen appears
unstable and shaky.
Check that the resolution and frequency of
the PC and graphics card are set within a
range compatible with the product. Then,
change the screen settings if required by
referring to ‘Preset Timing Modes’.
There are shadows or
ghost images left on
the screen.
Troubleshooting Guide
4
1,2
3
Connect the product and One Connect referring to the
image.
1 Following the steps 1-4 in the image, use One
Invisible Connection to connect the product and One
Connect.
2 Use the power cable to connect One Connect to a wall
outlet as shown in step 5.
* When arranging the remaining cable, refer to the
figure
for the correct arrangement.
CLASS 1 LASER PRODUCT (One Invisible Connection)
ꞏ Caution - Invisible laser radiation when open. Do not
stare into beam.
- Do not bend the One Invisible Connection cable
excessively. Do not cut the cable.
- Do not place heavy objects on the cable.
- Do not disassemble either of the cable connectors.
ꞏ Caution - Use of controls, adjustments, or the
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
One Connect
10 cm
Bending Cover
QP82R-8K
QP82R-8K
(M4 x L12)
x 1
One Connect
One Connect
One Connect
BN68-09675B-00_QSG_QPR-8K_INDIA_ENG.indd 1 2019-06-12 오전 9:48:40
To Next Page
Need help?
General
