Samsung R528 - Page 224

4-7
4. Troubleshooting
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
R530/R730
TP_NUMBER TP_LABEL Contents
0D4h TP_CPU_GET_STRING Get CPU brand string
050h TP_CPU_DISPLAY Display CPU type and speed
05Ah TP_DISPLAY_F2 Display "Press F2 for Setup" prompt - enable the keyboard interrupt
05Ch TP_MEMORY_TEST Size conventional memory, store the amount, print this to the screen.
060h TP_EXT_MEMORY Perform memory tests on extended RAM.
062h TP_EXT_ADDR Perform address tests on extended RAM
06Ah TP_DISP_CACHE Display cache RAM size if desired.
06Ch TP_DISP_SHADOWS Display BIOS shadow status
0CFh TP_ERROR_MSGS Display any errors found
072h TP_TEST_CONFIG Check for bad conguration
04Fh TP_MULTBOOT_INIT Allocates storage for the old and new history tables.
07Ch TP_HW_INTS initialize hardware interrupt vectors
096h TP_CLEAR_HUGE_ES
Perform a shutdown eight to transition from the warm start table to
the cold start table.
088h TP_BIOS_INIT
Initialize timeouts, key buffer, soft reset ag Initialize also shadow
ram data for memory size;
081h TP_LATE_DEVICE_INIT POST device initialization routine
087h TP_MCD_INIT
Each MCD device in the dedicated segment, calls the congure
routine.;
083h TP_FDISK_CFG_IDE_CTRLR Congure non-MCD IDE controllers.
089h TP_ENABLE_NMI Enable NMIs
090h TP_FDISK
Test hard disksIf the CMOS ram is valid and intact, and xed disks are
dened then call the xed disk init routine to intialize the xed disk
system and take over the appropriate interrupt vectors.
08Bh TP_MOUSE Setup PS/2 Mouse Interrupt & initialize Extended BDA
095h TP_CD Multiboot CD-ROM initialization
096h TP_CLEAR_HUGE_ES Exit big real mode
0AEh TP_CLEAR_BOOT Clear CongFailedBit and InPostBit in CMOS
091h TP_FDISK_FAST_INIT Program timing registers according to PIO modes
0C7h TP_DOCK_INIT_LATE SIO Initialization
09Eh TP_IRQS Enable the proper hardware interrupts
0A0h TP_TIME_OF_DAY Set time of day
0A2h TP_KEYLOCK_TEST Test if KeyLock or Keyboard Controller Password is on.
0C2h TP_PEM_LOG Invokes the error logging function of all registered error handlers
0BAh TP_DMI Execute DMI Handlers
0C3h TP_PEM_DISPLAY
Invoked via the shuctdown table at the end of postScans the
pemRegTbl and calls the display function for each registered
0A8h TP_ERASE_F2 Remove "Press F2" prompt from the screen
0AAh TP_SCAN_FOR_F2 Check if User has requested SETUP.
0ACh TP_SETUP_CHECK Check to see if SETUP should be executed
0D7h TP_FIRSTWARE_CHECK FirstSpace Check
0AEh TP_CLEAR_BOOT Clear CongFailedBit and InPostBit in CMOS
0B0h TP_ERROR_CHECK Check for POST errors
0B2h TP_POST_DONE Set/clear status bits to reect POST complete
0C5h TP_HOTKEY_END Mark the fact that we are no longer in POST
0BEh TP_CLEAR_SCREEN Cear the screen
0B6h TP_PASSWORD Query for password before boot
0D7h TP_FIRSTWARE_CHECK FirstSpace Check