EasyManua.ls Logo

Samsung SBB-MBOX - User Manual

Samsung SBB-MBOX
67 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
User Manual
© Samsung Electronics
Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Trademarks other than Samsung Electronics are
property of their respective owners.
SBB-MBOX
The color and the appearance may differ depending on the product, and the content in the
manual is subject to change without prior notice to improve the performance.
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect
(i.e., where the user manual has not been read).
(b) You bring the unit to a repair center, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
You will be informed of the administration fee amount before a technician visits.

Table of Contents

Other manuals for Samsung SBB-MBOX

Preview: Simple User Guide
Simple User Guide2 pages

Questions and Answers

  • V
    Vanessa MillerAug 10, 2025
    Why is Anynet+ not working on my Samsung SBB-MBOX?
    • L
      larrymartinezAug 10, 2025
      There are several reasons why Anynet+ might not be working. First, ensure the device is an Anynet+ compatible device, as the system only supports these. Check that the power cord and Video/HDMI cable of the Anynet+ device are properly connected. Also, verify that Anynet+ (HDMI-CEC) is enabled in the External Device Manager menu and that your remote control is Anynet+ compatible. Anynet+ may not function during the initial setup. If you've reconnected the HDMI cable, try rescanning for devices or power cycling your product. Finally, confirm that the Anynet+ function on the external device is enabled.
  • P
    Patricia LaneAug 17, 2025
    What to do if connected device is not displayed on Samsung Media Player?
    • P
      pattersonisaiahAug 17, 2025
      If a connected device isn't showing up, first check if it supports Anynet+ functions and that the HDMI cable is properly connected. Ensure Anynet+ (HDMI-CEC) is turned on in the External Device Manager menu. Try rescanning for Anynet+ devices. Anynet+ requires an HDMI connection, so ensure the device is connected with an HDMI cable. Note that some HDMI cables might not support Anynet+ functions. If there was a power failure or the HDMI cable was disconnected, repeat the device scan.
  • W
    William HuffmanAug 22, 2025
    How to start Anynet+ on Samsung SBB-MBOX Media Player?
    • E
      Eric MorganAug 22, 2025
      To start Anynet+, ensure the Anynet+ device is properly connected to the product. Then, verify that Anynet+ (HDMI-CEC) is set to 'On' in the External Device Manager menu.
  • P
    Pamela ButlerAug 28, 2025
    What to do if the message 'Disconnecting Anynet+ device...' appears on Samsung SBB-MBOX?
    • J
      jenniferromeroAug 29, 2025
      This message appears because the remote control cannot be used while configuring Anynet+ or switching to a view mode. Please wait until the product has completed the Anynet+ configuration or has finished switching to Anynet+ before using the remote control.
  • A
    Arthur CannonSep 3, 2025
    How to exit Anynet+ on Samsung SBB-MBOX Media Player?
    • W
      Whitney SimmonsSep 3, 2025
      To exit Anynet+, press the × button on the product remote control and select a non- Anynet+ device.

Samsung SBB-MBOX Specifications

General IconGeneral
ModelSBB-MBOX
CategoryMedia Player
ManufacturerSamsung
Video OutputHDMI
Audio OutputHDMI
Operating SystemUnknown
ConnectivityEthernet
Storage ExpansionUnknown

Related product manuals