Troubleshooting for Anynet+
I
iiiiij_:_!_i_i_i_i_i_i_i_iiiiiii_i_!!i_iii!!_i_iii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_iiii_iiii_ii_ii!!ii_iiiii_iiiiiiiiii_!_!_iiiii_i!i!iiiiiii¸
Anynet+ does not work.
ii_ !__iil_!_!_:_lli_i_i_!_i_!i!i!_i_i_i_i_ilil!lilllllll_!_iilililililililililililil_i_i_i!i!i!i_i_i_iiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiiiiii_i_i_i_i_i!i!i!i_iiiiiiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_ilililililililililililililililililililililililiiiiiii!_!i_ii!_i!!_!ii!i!ii!ii!_!i!i!i!i!i!i!i!i!i!i!i!iliiii_iii_i_iili_iiiiii_iiiiii_iii_i_!!i_i_i_i_i_i_i_i_i_i_!_!_!_!_!_!_!!_!_!_!_!_!_!_!i_!_:_i_i_i_i_ilililililililililililililililililililililililillllllli!i_i!ii_i!ii!ii!ii!ii!ii!ii!i_i!!i¸i!i!i!i!i!i!_!!!!!iiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i_!!i_i_i_i_i_i!_!i_i!!i!i!i!i!i!iiiiii_ii_!!_i_i_i_i_i_i_i_i_i_i_i_i_!!i_i_i_i_i_i_i_i_i_i!_!_!i!_i!_i!_i!_i!_i!_i!_i!i!_!_i!i!_iii!i!i!iii¸iii
• Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
• Onlyone receiver (home theater) can be connected.
• Check if the Anynet+ device power cord is properly connected.
• Check theAnynet+ device's Video/Audio/HDMI cable connections.
• Checkwhether Anynet+ (HDMI-CEC) isset to On in the Anynet+ setup menu.
• Checkwhether the TV remote control is in TV mode.
• Checkwhether the remote control isAnynet+ compatible.
• Anynet+ doesn't work in certain situations. (Searching channels, operating Media Play or Plug & Play (initial
setup), etc.)
• When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off
andon again.
Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+. • Check if the Anynet+ device is properly connected to the TV and check ifthe Anynet+ (HDMI-OEC) is set to
On in the Anynet+ Setup menu.
Pressthe TOOLS button to display the Anynet+ menu and select a menu you want.
I want to exit Anynet+. • Select View TV in the Anynet+ menu.
Pressthe SOURCE button on the TV remote control and select a non- Anynet+ device.
Press V CH A, PREoCH,and FAV,CH to change the TV mode. (Note that the channel button operates
onlywhen a tuner-embedded Anynet+ device is not connected.)
The message "Connecting to • You cannot use the remote controlwhen you are configuring Anynet+ or switching to aview mode.
Anynet+ device..." appears on the • Use the remote control when the Anynet+ setting or switching to view mode iscomplete.
screen.
The Anynet+ device does not play. • You cannot use the playfunction when Plug & Play (initialsetup) is in progress.
The connected device is not
displayed.
o
o
o
o
o
o
The TV Program cannot be
recorded.
The TV sound is not output • Connect the optical cable between TV andthe receiver.
through the receiver. • The ARC function enables digital output ofsound using the HDMI IN 2(ARC} port and can only be operated
when the TV is connected to an audio receiverthat supports the ARC function.
Checkwhether or not the device supports Anynet+ functions.
Checkwhether or not the HDMI cable is properly connected.
Checkwhether Anynet+ (HDMI-OEC) isset to On in the Anynet+ setup menu.
SearchAnynet+ devices again.
You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may not support Anynet+
functions.
Ifconnection isterminated because there has beersa power interruption or the HDMI cable has been
disconnected, please repeat the device scan.
Checkwhether the antenna jack on the recording device is properly connected.
English 47
To Next Page
Loading...
