Why do I need to replace the atomiser at regular intervals in Sanitas SIH 21?
To ensure the medication is delivered effectively, the nozzle holes must remain within a specific diameter. Regular replacement is also important for hygiene due to wear on the plastic from thermal and mechanical stress. Therefore, replace the atomiser regularly.
What to do if the Sanitas Medical Equipment atomiser produces little or no aerosol?
If your Sanitas Medical Equipment atomiser isn't producing enough aerosol, first check the amount of medicine in the atomiser, ensuring it's between 2 ml and 8 ml. Also, make sure the nozzles are not blocked; clean them if necessary. Ensure the atomiser is held upright and that the medicine solution is suitable for nebulizing, as specified by your doctor.
What to do if the output is too low in Sanitas SIH 21?
If the output of your Sanitas Medical Equipment is too low, check the hose for any kinks and the filter for any blockages.
Why does Sanitas Medical Equipment atomiser produce little or no aerosol?
If your Sanitas Medical Equipment atomiser is producing little to no aerosol, it could be due to several reasons. Ensure the medicine amount in the atomiser is correct, between 0.5 ml and 6 ml. Also, check for blockages in the nozzles and clean them carefully, poking from the underside if needed. Make sure the atomiser is held upright. Finally, the medicine solution might be unsuitable for nebulizing if it's too thick; consult your doctor for the appropriate solution.
Why do I need to replace the Sanitas Medical Equipment atomiser at regular intervals?
You need to replace the Sanitas Medical Equipment atomiser regularly for two main reasons. Firstly, to maintain a therapeutically effective particle spectrum, as the nozzle holes' diameter should not exceed a certain size, due to wear and tear on the plastic from thermal and mechanical stresses. This wear can alter the aerosol's droplet composition, affecting treatment effectiveness. Secondly, regular replacement is recommended for hygiene reasons.
What to do if the output of Sanitas SIH 21 Medical Equipment is too low?
If the output of your Sanitas Medical Equipment is too low, check the hose for any kinks. Also, inspect the filter for any blockages. Finally, verify that you are using the correct amount of inhalation solution.
What special steps should be taken for babies and children using Sanitas SIH 21 Medical Equipment?
When using Sanitas Medical Equipment for babies, ensure the mask covers both the mouth and nose for effective inhalation. For children, the mask should also cover the mouth and nose. Avoid nebulization next to a sleeping person, as it reduces the amount of medicine reaching the lungs. Children should only use the device with adult supervision, and never be left alone with the nebuliser.
Why does inhalation with the mask take longer with Sanitas Medical Equipment?
Inhalation with the mask takes longer with Sanitas Medical Equipment due to technical reasons. Less medicine is inhaled per breath through the mask holes compared to using the mouthpiece. The aerosol mixes with ambient air through these holes.
What to do if some inhalation solution remains in the Sanitas SIH 21 Medical Equipment atomiser?
It's normal for some inhalation solution to remain in the Sanitas Medical Equipment atomiser due to technical reasons. Stop inhalation if you notice a significant change in the atomiser's noise.
Why does inhalation with the mask take longer using Sanitas SIH 21?
Inhalation with the mask takes longer for technical reasons. Less medicine is inhaled per breath through the mask holes than when using the mouthpiece.
Details the intended use of the nebuliser for inhalation therapy of respiratory tract conditions.
Covers precautions for safe operation, electrical hazards, and proper handling of the device and its components.
Details proper usage, initial setup, malfunction handling, and guidelines for unit repair and maintenance.
Illustrates and lists the main components of the Sanitas SIH 21 nebuliser device.
Details the parts of the atomiser, including masks, mouthpiece, and medicine container.
Steps for setting up the device and cleaning accessories before first use.
Guidelines for safely connecting the device to the power supply and managing the power cord.
Instructions for assembling the atomiser, inserting the nozzle, and filling with medication.
Guidance on attaching masks/mouthpiece and performing the inhalation treatment.
Procedures for concluding inhalation and instructions for changing the air filter.
Instructions for cleaning the main unit and removing condensation from the air hose.
Detailed steps for disinfecting atomiser parts, accessories, and sterilisation methods.
Guidance on drying components, material wear, and proper storage of the nebuliser.
Addresses problems like low/no aerosol production and suitable medication queries.
Explains mask usage for children and reasons for atomiser replacement.
Details the SIH 21 model, type, dimensions, weight, and available spare parts.
Covers operating conditions, storage, aerosol properties, and sound pressure levels.
Provides information on the device's compliance with EMC standards and its intended electromagnetic environment.
General| Product color | Black, White |
|---|---|
| Nebulization capacity | 0.2 ml/min |
| AC input voltage | 230 V |
| Power source type | AC |
| AC input frequency | 50 Hz |
| Dimensions (WxDxH) | 178 x 295 x 94 mm |
| Adult mask | Yes |
Weight and Dimensions| Weight | 1600 g |
|---|
To Next Page
