How to fix a stuck Emergency Stop Button on Sankosha DF-100E-V3?
If the Emergency Stop Button on your Sankosha Finishers is stuck, first, ensure safety by releasing the Emergency Stop Button. Turn the button clockwise and then push the Reset Button. If the E1 error persists even after releasing the button, there may be a wiring issue. Inspect the button itself or check for any cuts in the wire.
What to do if there is an Inverter Error on Sankosha Finishers?
If your Sankosha Finishers machine stops due to an inverter problem, turn the power off and wait for at least two minutes to allow the inverter to cool down. Then, turn the machine back on. If the error persists, contact your dealer or Sankosha.
What to do if there is an Auto Start Button Error on Sankosha Finishers?
If the Auto Start Button on your Sankosha Finishers is showing an error, and the 'E28' error appears even when the button is not pressed, it indicates a button problem. Check if the switch is broken or if the wire connection is loose or disconnected. If the button is physically stuck, release the button and remove any obstructions. Then, press the Reset button to return the machine to its original position.
What to do if the Multi Function Foot Pedal on Sankosha Finishers is not working?
If the Multi Function Foot Pedal on your Sankosha Finishers shows an error, and the 'E24' error appears even when the pedal is not pressed, it indicates a switch (FP03) problem. Check if the switch is broken or if the wire connection is loose or disconnected. If the pedal is physically stuck, release the pedal and remove any obstructions. Then, push the Reset button to return the machine to its original position.
What to do if the Shoulder Expander Foot Pedal on Sankosha DF-100E-V3 is not working?
If the Shoulder Expander Foot Pedal on your Sankosha Finishers shows an error, and the 'E25' error appears even when the pedal is not pressed, it indicates a switch (FP01) problem. Check if the switch is broken or if the wire connection is loose or disconnected. If the pedal is physically stuck, release the pedal and remove any obstructions. Then, push the Reset button to return the machine to its original position.
What to do if the Body Down Foot Pedal on Sankosha DF-100E-V3 is not working?
If the Body Down Foot Pedal on your Sankosha Finishers shows an error, and the 'E26' error appears even when the pedal is not pressed, it indicates a switch (FP04) problem. Check if the switch is broken or if the wire connection is loose or disconnected. If the pedal is physically stuck, release the pedal and remove any obstructions. Then, push the Reset button to return the machine to its original position.
What to do if the Body Up Foot Pedal on Sankosha Finishers is not working?
If the Body Up Foot Pedal on your Sankosha Finishers shows an error, and the 'E27' error appears even when the pedal is not pressed, it indicates a switch (FP02) problem. Check if the switch is broken or if the wire connection is loose or disconnected. If the pedal is physically stuck, release the pedal and remove any obstructions. Then, push the Reset button to return the machine to its original position.
What to do if there is a Rotation Button Error on Sankosha DF-100E-V3 Finishers?
If the Rotation Button on your Sankosha Finishers is showing an error, and the 'E23' error appears even when the button is not pressed, it indicates a button problem. Check if the switch is broken or if the wire connection is loose or disconnected. If the button is physically stuck, release the button and remove any obstructions. Then, press the Reset button to return the machine to its original position.
What to do if there is a Steam Button Error on Sankosha DF-100E-V3 Finishers?
If the Steam Button on your Sankosha Finishers is showing an error, and the 'E22' error appears even when the button is not pressed, it indicates a button problem. Check if the switch is broken or if the wire connection is loose or disconnected. If the button is physically stuck, release the button and remove any obstructions. Then, press the Reset button to return the machine to its original position.
What to do if there is a Blower Button error on Sankosha DF-100E-V3?
If the Blower Button on your Sankosha Finishers is showing an error, and the 'E21' error appears even when the button is not pressed, it indicates a button problem. Check if the switch is broken or if the wire connection is loose or disconnected. If the button is physically stuck, release the button and remove any obstructions. Then, press the Reset button to return the machine to its original position.
To Next Page
General