Santerno DCREG2 Series User Manual

• 15P0059B3 •
DCREG2
DCREG4
USER MANUAL
28/05/18 R.07
SOFTWARE VERSION D5.02
• This manual is an integral and essential part of the product. Carefully read the instructions contained
herein as they provide important hints for use and maintenance safety.
• This device shall be used only for the purposes it is aimed at. Any other use is to be considered as
improper and dangerous. The manufacturer is not responsible for any possible damage caused by
improper, erroneous and irrational uses.
• Elettronica Santerno are responsible for the device in its original setting.
• Any changes to the structure or operating cycle of the device must be performed or authorized by
Elettronica Santerno’s Engineering Department.
• Elettronica Santerno are not responsible for the consequences resulting from the use of non-original
spare parts.
• Elettronica Santerno reserve the right to make any technical changes to this manual and the device
without prior notice. Any misprint or spelling mistake will be edited in the new versions of this manual.
• Elettronica Santerno are responsible for the information contained in the original version of the Italian
manual.
• The information contained herein is Elettronica Santerno’s property and cannot be reproduced.
Elettronica Santerno enforce their rights on the drawings and catalogues according to the law.
Elettronica Santerno S.p.A.
Via della Concia, 7 – 40023 Castel Guelfo (BO) Italy
Tel. +39 0542 489711 - Fax +39 0542 489722
santerno.com info@santerno.com
E n g l i sh

Santerno DCREG2 Series Specifications

General

Brand	Santerno
Model	DCREG2 Series
Category	Media Converter
Language	English

Summary

START-UP

PRELIMINARY CHECKS

MAIN CHECKS AND CONFIGURATIONS

Procedures for initial setup, status checks, and parameter configuration.

SPEED CONTROL MODE OPERATION

RAMP CONFIGURATION IN SPEED CONTROL MODE

SPEED CONTROL OPTIONS

CURRENT (TORQUE) CONTROL MODE OPERATION

CURRENT LIMIT CONTROL OPTIONS

ANALOG AND DIGITAL OUTPUTS

BACKUP AND RESTORATION OF STORED PARAMETERS

GENERAL CHARACTERISTICS

RATINGS

Technical specifications and ratings for DCREG2/DCREG4 models.

DCREG SIZE 1...2A POWER CONNECTIONS

Wiring diagram for DCREG Size 1 to 2A power connections up to 500 Vac.

DCREG MODULAR.S POWER CONNECTIONS

Wiring diagram for DCREG MODULAR.S power connections up to 500 Vac.

DCREG MODULAR.S POWER UNIT WIRING DIAGRAM

DCREG MODULAR.S CONTROL UNIT TERMINALS

SUPPLY AND POWER TERMINALS

Description of all supply and power terminals for DCREG drives.

CROSS-SECTIONS OF THE POWER CABLES AND SIZES OF THE PROTECTIVE DEVICES

Guidelines for selecting power cable cross-sections and protective devices.

UL-APPROVED FUSES

Recommended UL-approved fuses for DCREG drive protection.

SHORT-CIRCUIT CURRENT

Rating information regarding short-circuit current withstand capability.

CONVERTER AND MOTOR GROUND CONNECTION

Procedures and requirements for proper grounding of DCREG and motor.

DCREG SIGNAL CONNECTIONS

Diagram illustrating signal connections for the DCREG drive.

SIGNAL TERMINALS

Detailed list and description of all signal terminals and their functions.

LEDS AND TEST POINTS ON THE CONTROL BOARD

FEEDBACK FROM ENP/NR

MILLIAMPERE INPUT / OUTPUT SIGNALS

KEYPAD AND ALPHANUMERIC DISPLAY

KEYS OPERATING MODES

FUNCTIONS DISPLAYED BY THE LEDS

LOCAL OPERATING MODE

How to operate the drive using the keypad in local mode.

SPECIAL FEATURES

AUTOTUNING

Procedures for automatic tuning of motor and load characteristics.

RAMPS OVER THE REFERENCE

MOTOR POTENTIOMETER

CURRENT LIMITATION

Parameters controlling the maximum current output based on speed.

OPERATION QUADRANTS

MOTOR HEATING THERMAL IMAGE

FIELD REGULATOR

Setting and dynamic regulation of the field current for motor control.

CONFIGURABLE DIGITAL OUTPUTS

ADAPTIVE SPEED PARAMETERS

Automatic adjustment of speed loop gains and integral times for performance.

ELECTROMAGNETS APPLICATION

OPERATION PARAMETERS

MEASURE PARAMETERS

PROGRAMMING PARAMETERS

Parameters marked with 'P' that can be modified by the user for drive configuration.

CONFIGURATION PARAMETERS

Parameters marked with 'C' for configuring drive functions and settings.

DIAGNOSTICS

ALARM PARAMETERS

List and explanation of alarm codes (Axxx) displayed on the Status page.

WARNING PARAMETERS

List and explanation of warning codes (Wxxx) indicating specific conditions.

EMC CHARACTERISTICS AND INPUT FILTER

EMISSION LIMITS

FIRST ENVIRONMENT FILTERS

Filter types required for drives connected to the First Environment grid.

SECOND ENVIRONMENT FILTERS

Filter types required for drives in the Second Environment.