Rear Terminals
Connecting other equipment
You can connect a VCR, S-VHS VCR, Satellite Tuner, PAY TV Decoder, DVD
or Camcoder to this TV via the SCART terminal and the RCA terminals.
This TV set has the following rear terminals:
- AV1: scart which has RGB and composite video signal inputs and TV
output.
- AV2: RCA Audio/video input.
n Depending on the type of video tape or connected AV equipment being
used, it may be necessary to select colour system. In this case, press
the Recall/System button and select a suitable colour system. Colour
system setting for AV position is automatically stored in the memory.
n Connect the VCR or DVD right and left audio output to the correspon-
ding left (l) and right (r) input channels. By pressing the Stereo/Mono
button repeatedly, you can select the sound track L (left), R (right) or
L/R.
n You can select and return to a TV programme by selecting any of the TV
position while watching a playback from a VCR, DVD, etc.
n By pressing the button on your remote control you can change
the source of the input signal. The sequence is the following:
Helpful Hints
n NO PICTURE, NO SOUND
l Check if TV is plugged in.
l Try a different channel, if OK, probably station trouble.
l Try to switch on the TV pressing the red stand-by key from the remote
control.
n POOR PICTURE, SOUND OK
l Adjust BRIGHTNESS, CONTRAST control.
l Adjust FINE TUNING control.
l Check aerial connections.
n NO COLOUR, PICTURE OK
l Adjust COLOUR control.
l Adjust FINE TUNING control.
l Is the programme in colour?
n WEAK PICTURE
l Check aerial connections on back of set.
l Check aerial for broken wires.
l Re-orient aerial.
n POOR SOUND QUALITY
l Check the sound system in “Preset menu”.
n The following faults are not caused by the receiver:
"GHOSTS"
Reflections of signals from mountains or high buildings will cause multiple
images, called "Ghosts". These abnormal conditions can be reduced to
minimum by repositioning aerial or by installing a new one suited for your
area.
"INTERFERENCE"
Interference may be caused by electrical appliances, car ignition systems,
etc. This should normally be a temporary condition, but should this inter-
ference persist, contact your dealer.
Specifications
Power source (20”) AC 220~240V C.A. 50Hz
(15”) Input: 100V-240V ~ 1.2A Max.50/60Hz
Output:12V
---
3.4A
Television system System I
Colour system PAL/NTSC (in mode AV)
Channel coverage UHF:21-69
CATV:X,Y,Z,S1-S41, B-Q
Aerial input impedance 75 ohm
AV Terminal
AV1: CENELEC Standard.
Input: Composite video, S-VHS, RGB and audio-L/R.
Output:TV-output with composite video and audio-L/R.
AV2: RCA jacks.
Input: Composite video and audio-L/R.
Headphone socket Stereo jack 3mm
CE15LC4-B
CE20LC4-B
Sound output 2x2W (RMS) 2x2W (RMS)
Picture panel (inches) 38cm./15" 51cm./20"
Dimensions WxHxD(mm) 470x337x191 590x430,5x191
(with stand base)
Dimensions WxHxD(mm) 470x299x88 590x393,7x87,5
(without stand base)
Weight (kg) (w/stand) 4,4 7
Picture resolution XGA 1024 (Horiz.) VGA 640 (Horiz.)
768 (Vert.) píxeles 480 (Vert.) píxeles
Viewing angles Horiz. 120° Horiz. 160°
Vert. 100° Vert. 140°
Contrast ratio 500:1 500:1
Brightness 500cd/m2 500cd/m2
Response time 10 ms. 16 ms.
Due to SANYO's continuous improvement of quality policy, these data can
change without previous notice.
__
8
42251811.qxd 20/05/2005 19:06 PÆgina 9
To Next Page
Loading...
