Sanyo DS19500 - Page 27

DS19500
Model:
COLOR TELEVISION
AS
FILE NO.
G8FGM, PRODUCT CODE 111350180
REFERENCE No. SM5110088-04
Notice
CORRECTION
SERVICE FLASH
PRODUCTION CHANGE
ADD INFORMATION
Please add this notice to the Service Manual listed below.
REVISION 4
Category:
U.S.A. / CANADA
Destination:
JULY / 26 / 2001
Date:
19500-04
Effective from: Chassis No.
SM5110088
REF: No.
NOTE: Match the Chassis No. on the unit’s back cover with the Chassis No. in the Service Manual.
If the Service Manual Chassis No. does not match the unit’s, additional Service Literature is
required. This chassis is similar to Chassis No. 19500-00. Only the Difference Service
Information is given in this manual. For detailed Service Information, refer to the Original Service
Manual and Notices for Chassis No. 19500-00 used in Model DS19500 (SM5110088).
Note: The change in Initial Bus Data Setup above is also effective in Chassis No. 19500-01.
INITIAL BUS DATA SETUP
Note: When IC802 (EEPROM) is replaced, the Service Menu NO. 01 HP (H Phase), NO. 13 TDS (Trap & D SW), NO. 24 AG (AFC
Gain), NO. 26 SCO (Sub-Color), NO. 27 STI (Sub-Tint), NO. 28 SSH (Sub-Sharpness), NO. 29 OPT (Option 1), NO. 30 OP2
(Option 2),NO. 31 HR (OSD Display H-Position), NO. 60 R00 (ROM Data 0), NO. 61 R01 (ROM Data 1), NO. 64 R04 (ROM
Data 4), NO. 68 R08 (ROM Data 8), NO. 70 R10 (ROM Data 10), NO. 71 R11 (ROM Data 11), NO. 72 R12 (ROM Data 12),
NO. 73 R13 (ROM Data 13), NO. 74 R14 (ROM Data 14), NO. 75 R15 (ROM Data 15), NO. 76 R16 (ROM Data 16), NO. 77
R17 (ROM Data 17), NO. 78 R18 (ROM Data 18) and NO. 132 R72 (ROM Data 72) should be set up for proper TV opera-
tion before attempting the service adjustments.
1. Disconnect the AC power cord (AC 120V line).
2. While pressing the MENU key, reconnect the AC power cord. The Service Menu display will now appear.
3. Select NO. 01 HP (H Phase) with ▲ or ▼ key. Adjust the data with + or – key for 18.
4. Select NO. 13 TDS (Trap & D SW) with ▲ or ▼ key. Adjust the data with + or – key for 1.
5. Select NO. 24 AG (AFC Gain) with ▲ or ▼ key. Adjust the data with + or – key for 0.
6. Select NO. 26 SCO (Sub Color) with ▲ or ▼ key. Adjust the data with + or – key for 7.
7. Select NO. 27 STI (Sub Tint) with ▲ or ▼ key. Adjust the data with + or – key for 21.
8. Select NO. 28 SSH (Sub Sharpness) with ▲ or ▼ key. Adjust the data with + or – key for 10.
9. Select NO. 29 OPT (Option 1) with ▲ or ▼ key. Adjust the data with + or – key for 100.
10. Select NO. 30 OP2 (Option 2) with ▲ or ▼ key. Adjust the data with + or – key for 0.
11. Select NO. 31 HR (OSD Display H-Position) with ▲ or ▼ key. Adjust the data with + or – key for 30.
11a. Select NO. 60 R00 (ROM Data 0) to NO. 132 R72 (ROM Data 72) with ▲ or ▼ key and adjust each of the data with + or
– key as specified in Table 1 in the following pages.
12. Press the MENU key to turn off the Service Menu display.
1. IN THE SERVICE ADJUSTMENTS LIST
PAGE 3