Sanyo DS19500 - Page 28

— 2 —
Table 1. ON-SCREEN SERVICE MENU
When IC802 (EEPROM) is replaced, check the bus data to confirm they are the same as below. The shaded menu should be
checked and be set up or readjusted according to the procedures described in the following pages. Initial Setup Data marked with
an * should be changed from Initial Reference Data. (See page 3 for Initial Bus Data Setup.)
NO. TITLE
INITIAL REFERENCE INITIAL SETUP
RANGE OF DATA FUNCTION
DATA DATA
01 HP 15 18* 0~31 Horizontal Phase (Horizontal Centering)
02 IAS 0 0 0, 1 IF AGC Switch 0: TV (Normal) 1: AV (IF Gain Minimum)
03 RAD 25 25 0~63 RF AGC Delay
04 PT 64 64 0~127 PLL Tuning
05 ADA 31 31 0~63 APC Detect Adjust
06 CD 0 0 0, 1 C-Diff
07 VS 32 32 0~63 Vertical Size
08 RB 0 0 0~255 Red Bias
09 GB 0 0 0~255 Green Bias
10 BB 0 0 0~255 Blue Bias
11 RD 60 60 0~127 Red Drive
12 BD 60 60 0~127 Blue Drive
13 TDS 0 1* 0, 1 Trap & D (B.P.F.) Switch 0: OFF 1: ON
14 AF 0 0 0, 1 Auto Flesh 0: OFF 1: ON
15 BS 0 0 0, 1 Black Stretch
1: OFF 0: ON
16 VL 4 4 0~7 Video Level
17 FL 15 15 0~31 FM Level
18 NIS 1 1 0, 1 N/I Switch (Black Noise Inverter)
1: OFF 0: ON
19 ABL 1 1 0,1 ABL Defeat 0: OFF 1: ON
20 WP 1 1 0,1 White Peak Limiter 1: OFF 0: ON
21 GD 7 7 0~15 Green Drive Reduction
22 VC 0 0 0~7 Vert. Comp
23 VD 32 32 0~63 Vert. DC
24 AG 3 0* 0~3 AFC Gain
00: Auto 01: High Gain 10: Low Gain 11: Non-Gate
25 SB 32 32 0~63 Sub-Brightness
26 SCO 10 7* 0~31 Sub-Color
27 STI 14 21* 0~31 Sub-Tint
28 SSH 8 10* 0~15 Sub-Sharpness
29 OPT 32 100* 0~255 Option 1 (See Note 1 page 5.)
30 OP2 64 0* 0~255 Option 2 (See Note 2 page 5.)
31 HR 43 30* 0~63 H-Position (OSD H-Position)
32 ATT 15 15 0~15 Attenuation
33 STE N/A N/A N/A N/A
34 FIL N/A N/A N/A N/A
35 WDB 32 32 0~32 Wide Band
36 SPC 32 32 0~32 Spectral
37 SPV N/A N/A N/A N/A
38 SBO 5 5 0~255 Sub Bright Offset
39 PCO N/A N/A N/A N/A
40 PTI N/A N/A N/A N/A
41 PUV N/A N/A N/A N/A
42 PDV N/A N/A N/A N/A
43 PLH N/A N/A N/A N/A
44 PRH N/A N/A N/A N/A
45 PCN N/A N/A N/A N/A
46 PBS N/A N/A N/A N/A
47 DRV
0~127 Red drive Adjustment (See Note 3 page 5.)
0~127 Blue Drive Adjustment (See Note 3 page 5.)
– 0 0 0~255 Red Bias Adjustment (See Note 4 page 5.)
48 – 0 0 0~255 Green Bias Adjustment (See Note 4 page 5.)
– 0 0 0~255 Blue Bias Adjustment (See Note 4 page 5.)
60 R00 0 231* 0~255 ROM Data 0
61 R01 0 151* 0~255 ROM Data 1
62 R02 0 0 0~255 ROM Data 2
1. IN THE SERVICE ADJUSTMENTS LIST (Continued)
PAGE 4